Dell EMC E68S Installation And Service Manual Download Page 56

Page: 56 / 187

Figure 49. 16 x 2.5-inch drive backplane

1. BP_DST_SB1 (backplane to front PERC)

2. BP_PWR_1 (backplane power and signal cable to system

board)

3. BP_PWR_CTRL (front PERC power and control signal)

4. BP_DST_SA1 (backplane to front PERC)

Figure 50. 24 x 2.5-inch drive backplane

1. DST_PB6 (PCIe/NVMe connector)

2. DST_PA6 (PCIe/NVMe connector)

3. DST_PB5 (PCIe/NVMe connector)

4. DST_PWR_2 (backplane power and signal cable to system

board)

5. DST_PA5 (PCIe/NVMe connector)

6. DST_PB4 (PCIe/NVMe connector)

7. DST_PA4 (PCIe/NVMe connector)

8. DST_PB3 (PCIe/NVMe connector)

9. DST_PA3 (PCIe/NVMe connector)

10. DST_PB2 (PCIe/NVMe connector)

11. DST_PWR_1 (backplane power and signal cable to system

board)

12. DST_PA2 (PCIe/NVMe connector)

13. DST_PB1 (PCIe/NVMe connector)

14. DST_PA1 (PCIe/NVMe connector)

Removing the drive backplane

Prerequisites

CAUTION:

To prevent damage to the drives and backplane, remove the drives from the system before removing

the backplane.

CAUTION:

Note the number of each drive and temporarily label them before you remove the drive so that you

can reinstall them in the same location.

NOTE:

The procedure to remove the backplane is similar for all backplane configurations.

1. Follow the safety guidelines listed in the

Safety instructions

on page 26.

2. Follow the procedure listed in the

Before working inside your system

on page 27.

Remove the backplane cover

4. If installed,

remove the air shroud

Remove all the drives

Remove the cooling fan cage assembly

7. Disconnect the drive backplane cables from the connector on the system board.
8. Disconnect the drive backplane cables from the connector on the backplane.

Installing and removing system components

Summary of Contents for E68S




























































































































































































Search results

Summary of Contents for E68S

Reviews:

Related manuals for E68S

Brands by name

Popular brands

Dell EMC E68S, Installation And Service Manual

Search results

Summary of Contents for E68S

Reviews:

Related manuals for E68S

Brands by name

Popular brands