background image

Part Number: 9291456  11/17

Installation 

Section 2

N225 & N227 STANDARD INSTALLATION DETAILS
For any non-standard installation consult the factory.

1.  Install a GFCI receptacle a minimum of 14” (36cm) up 

from the cabinet bottom inside the partitions.

2.  Cabinet interior minimum dimensions:

Dimensions

N225-E, N225P

N227-E, N227P

A

21.50” (55cm)

29.62” (75cm)

B

29.38” (75cm)

29.38” (75cm)

C

26.00” (66cm)

26.00” (66cm)

D

16.12” (41cm)

29.62” (75cm)

E

26.62” (68cm)

26.62” (68cm)

F

Minimum 2.75” (7cm), Maximum 7.0” (18cm)

23.50”

(60cm)

C

E

D

A

B

12.0”

(30cm)

14.0”

(36cm)

10.0”

(25cm)

F

3.  Place the condensing unit through the counter cutout.
4.  Extend the telescoping duct from the front of the 

condensing unit to the back of the louver. Export 

models do not have a telescoping duct, skip to step 6.

5.  Put eight provided screws through the telescoping 

duct side walls to hold it at the desired depth.

Use Screws to Secure Desired Depth 

3 of 8 Screws Shown

6.  Partitions must fully extend front to back and top to 

bottom.

7.  Louver cutout must extend to bottom of cabinet and 

align with condenser face. 
NOTE: The louver provided must be installed in front of 

the condensing unit’s finned coil. Any restriction to the 

proper air flow will void the compressor warranty.

•  Louver measures 13.00” x 25.00” (33cm x 64cm).
•  Louver Cutout Size is 12.00” x 23.50” (30cm x 60cm) 

(typical installation).

Finned C

oil

Duct

Partitions Not Shown

Louv
er

Typical Counter Cabinet

Summary of Contents for 200 Series





















Reviews: