background image

5  Electrical installation

5.1  Electrical connection of the DeLaval

swinging cow brush SCB3

Danger!
Risk of electric shock!

The electrical installation or any

work on the electrical equipment

must be done by an authorised elec-

trician. The work must also be per-

formed in accordance with national

regulations.

The DeLaval swinging cow brush SCB3 should

be installed by an authorized electrician, in

accordance with local regulations.

The DeLaval swinging cow brush SCB3 must be

connected to an earthed power supply socket

equipped with or supplied by a Residual Current

Device (RCD), also known as a Ground Fault

Circuit Interrupter (GFCI), rated according to

local regulations.

For US and Canada, the machine must be con-

nected to a grounded, metal, permanent wiring

system; or an equipment-grounding conductor

must be run with the circuit conductor and con-

nect to the equipment-grounding terminal or lead

on the machine.

Ensure to protect supply cord route from damage

and/or chewing by cows.

If the supply cord is damaged, it must be replaced

by an authorized person, in order to avoid haz-

ard.

Note! The motor is protected against overloads

by means of a built-in thermal protection. After

cooling down of the motor, this thermal protection

will automatically be reset.

Note! For safety reasons, turn the switch to the

OFF position and switch OFF the mains before

starting any job at the electric installation.

DeLaval swinging cow brush SCB3

Installation

© DeLaval 2016.

2016-07-19, Version 5

18 (26)

84948801

Summary of Contents for SCB3



























Reviews: