background image

 

 

DTE-3114 – Networked Quad QAM Modulator 

 

 

USER 

MANUAL

 

 

13 

 
C:\>route print 
=========================================================================== 
Interface List 
0x1 ........................... MS TCP Loopback interface 
0x2 ...00 14 f4 00 00 2b ...... DekTec DTA-160 Gigabit Ethernet Port 
0x3 ...00 1c c0 38 60 33 ...... Intel(R) 82566DC-2 Gigabit Network Connection 
=========================================================================== 
=========================================================================== 
Active Routes: 
Network Destination        Netmask          Gateway       Interface  Metric 
          0.0.0.0          0.0.0.0  192.168.100.100  192.168.100.28       20 
        127.0.0.0        255.0.0.0        127.0.0.1       127.0.0.1       1 
      169.254.0.0      255.255.0.0    192.168.200.3   192.168.200.3       1 
    192.168.100.0    255.255.255.0   192.168.100.28  192.168.100.28       20 
   192.168.100.28  255.255.255.255        127.0.0.1       127.0.0.1       20 
  192.168.100.255  255.255.255.255   192.168.100.28  192.168.100.28       20 
    192.168.200.0    255.255.255.0    192.168.200.3   192.168.200.3       10 
    192.168.200.3  255.255.255.255        127.0.0.1       127.0.0.1       10 
  192.168.200.255  255.255.255.255    192.168.200.3   192.168.200.3       10 
        224.0.0.0        240.0.0.0   192.168.100.28  192.168.100.28       20 
        224.0.0.0        240.0.0.0    192.168.200.3   192.168.200.3       10 
  255.255.255.255  255.255.255.255   192.168.100.28  192.168.100.28       1 
  255.255.255.255  255.255.255.255    192.168.200.3   192.168.200.3       1 
Default Gateway:   192.168.100.100 
=========================================================================== 
Persistent Routes: 
  None 

The link-local route is now present and communication with the DTE-3114 is possible. 

Example 2: 

Same situation as example 1, but now the "

route print"

 gives the following result: 

 
C:\>route print 
=========================================================================== 
Interface List 
0x1 ........................... MS TCP Loopback interface 
0x2 ...00 14 f4 00 00 2b ...... DekTec DTA-160 Gigabit Ethernet Port 
0x3 ...00 1c c0 38 60 33 ...... Intel(R) 82566DC-2 Gigabit Network Connection 
=========================================================================== 
=========================================================================== 
Active Routes: 
Network Destination        Netmask          Gateway       Interface  Metric 
          0.0.0.0          0.0.0.0  192.168.100.100  192.168.100.28       20 
        127.0.0.0        255.0.0.0        127.0.0.1       127.0.0.1       1 
      169.254.0.0      255.255.0.0   192.168.100.28  192.168.100.28       1 
      169.254.0.0      255.255.0.0    192.168.200.3   192.168.200.3       1 
    192.168.100.0    255.255.255.0   192.168.100.28  192.168.100.28       20 
   192.168.100.28  255.255.255.255        127.0.0.1       127.0.0.1       20 
  192.168.100.255  255.255.255.255   192.168.100.28  192.168.100.28       20 
    192.168.200.0    255.255.255.0    192.168.200.3   192.168.200.3       10 
    192.168.200.3  255.255.255.255        127.0.0.1       127.0.0.1       10 
  192.168.200.255  255.255.255.255    192.168.200.3   192.168.200.3       10 
        224.0.0.0        240.0.0.0   192.168.100.28  192.168.100.28       20 
        224.0.0.0        240.0.0.0    192.168.200.3   192.168.200.3       10 
  255.255.255.255  255.255.255.255   192.168.100.28  192.168.100.28       1 
  255.255.255.255  255.255.255.255    192.168.200.3   192.168.200.3       1 
Default Gateway:   192.168.100.100 
=========================================================================== 
Persistent Routes: 
  None 

In this routing table two link-local routes are present: one from network interface 192.168.100.28 

and  one  from  192.168.200.3.  Dual  routes  can  result  in  incorrect  communication  with  the 

Summary of Contents for DTE-3114



















































Reviews: