Deif Multi-line 2 Description Of Options Download Page 9 | Manualshive

Page: 9 / 19

background image

GPC, PPU

Option O1, Water turbine control

DEIF A/S

Page 9 of 19

System setup

The values corresponding to 4mA and 20mA must be adjusted in the menus 4042 and 4043.

Menu Description

Comments

404X

Water level nominal

This value corresponds to the 20mA value of the transducer.

404X

Water level minimum

This value corresponds to the 4mA value of the transducer.

This can be adjusted from the USW or from the display.

The 4mA value can be adjusted negative. This is to be able to stop the
regulation (see the description of ‘Water level regulation’ on page 10).

«
...
7
8
9
10
11
...
»

Summary of Contents for Multi-line 2




















Reviews:

No comments

Related manuals for Multi-line 2

Brand: ABB Pages: 2

Brand: 7bit Pages: 2

Brand: Jafar Pages: 15

Brand: Samson Pages: 56

Brand: Hach Pages: 128

Brand: Yamato Pages: 33

Elemec3 013-02-0095-002

Brand: GAI-Tronics Pages: 12

Brand: Harman Pages: 2

Brand: T-Link Pages: 3

CentriPro Aquavar SOLO

Brand: Xylem Pages: 48

Brand: Alde Pages: 36

YQPV-HP360V/100A

Brand: PSC Solar Pages: 22

Brand: Procom Pages: 10

LOWARA Aquavara IPC

Brand: Xylem Pages: 292

ibaMS16-DI-220V Series

Brand: IBA Pages: 32

Brand: hotset Pages: 2

PersonalWorkplace Pro Video

Brand: G&D Pages: 56

Brand: Beninca Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands