DEI Rattler 100 Installation Manual Download

Page: 23 / 26

operating settings learn routine

™

Many of the operating settings of this unit are programmable. They can be changed whenever necessary through

the operating settings learn routine.

Key.

Turn the ignition on and then back off. (The H1/9 YELLOW switched ignition input

must be connected.)

Choose.

Within 10 seconds, press and release the Valet

/Program switch the number of

times corresponding to the feature number you want to program (see the

Features Menu

section of this guide). The LED ON settings listed in the

Features Menu

table are the factory

default settings.

Once the Valet/Program switch has been pressed and released the number of times corre-

sponding to the feature you wish to program, press it once more and

HOLD

it. After a second,

the LED will flash to indicate which feature you have accessed. For example, groups of five

flashes would indicate access to Feature 5. The horn will also honk five times (if connected).

Transmit.

While holding the Valet®/Program switch, you can select the desired feature set-

tings using the remote transmitter. As shipped, the unit is configured to the default LED

ON settings. Pressing the Channel 1 transmitter button (usually Button I) while holding

down the Valet/Program switch will program the feature to the LED ON setting. The LED will

light solid (stop flashing) to indicate the setting. The horn will honk once (if connected).

Pressing the Channel 2 transmitter button (usually Button II) while holding down the

Valet/Program switch will change the setting to the LED OFF setting. The LED will turn off

indicating the change and the horn will honk twice (if connected).

Release.

The Valet

/Program switch can now be released.

For example, to program Feature 1 from ON to OFF, within 10 seconds of turning the ignition off, press and release

the Valet

/Program switch once. Then press it again and

HOLD

it. The LED will flash in groups of one and the

horn will honk once (if connected). While holding the Valet

/Program switch, press the Channel 2 transmitter

button. The LED will stop flashing and go out. The horn will honk twice if connected. The ignition-controlled door

locks feature has now been programmed off. If this is not the desired setting, without releasing the

Valet

/Program switch, press the Channel 1 button on the transmitter. The LED will light solid and the horn will

honk once if connected. The ignition-controlled door locks feature has now programmed on. Release the

Valet

/Program switch after the desired selection has been made.

Summary of Contents for Rattler 100



























Search results

Summary of Contents for Rattler 100

Reviews:

Related manuals for Rattler 100

Brands by name

Popular brands

DEI Rattler 100, Installation Manual

Search results

Summary of Contents for Rattler 100

Reviews:

Related manuals for Rattler 100

Brands by name

Popular brands