background image

18

©

1999 Directed Electronics, Inc.

Timer Mode automatically starts your vehicle engine and runs it for

a pre-programmed time period, every three hours for a total of six

operation cycles. Timer Mode helps to ensure that your engine will

start in the morning after being parked outside during a night of

extremely cold temperatures. 

IMPORTANT!

This feature must only be used in open areas, never in an

enclosed area such as a garage. 

To enter Timer Mode:

1.

Start the vehicle by pressing and releasing 

and 

on the

transmitter.

2.

Press and release 

on the transmitter.

3.

Within two seconds, press and release 

and 

on the

transmitter again.

4.

The engine will shut down and the parking lights will flash

four times. The engine will then restart to confirm that Timer

Mode has been entered.

The vehicle engine may be allowed to run for its pre-programmed

time period, or it can be shut down while running during Timer

Mode operation by pressing buttons 

and 

on the transmit-

ter again. In either case, the vehicle will restart every three hours

for a total of six operation cycles. If the system receives a shut-

down input while the engine is running in Timer Mode, the engine

will stop, but will restart, on schedule, again in three hours!

Timer Mode

Summary of Contents for 6500ESP






































Reviews: