background image

11

©

1999 Directed Electronics, Inc.

Pressing 

a second time within five seconds: The siren

chirps twice followed by a long chirp. Zone 2 is now

bypassed.

Pressing 

a third time within five seconds: The siren chirps

three times followed by a long chirp. Zone 4 is now bypassed.  

Pressing 

a fourth time within five seconds: The siren

chirps four times followed by a long chirp. Zones 2 and 4 are

now bypassed.

Pressing 

a fifth time within five seconds: The siren chirps

five times followed by a long chirp. All input zones, except

the ignition, are now bypassed.

NOTE:

Multi-Level Security Arming only applies to a single arming cycle.

Once the system is disarmed and then re-armed, all the zones will be
active again.

Your security system can be armed while driving the vehicle!

Simply press 

on the transmitter while the vehicle is running.

The siren will chirp once to indicate that the security system is

armed, and then once more to indicate that the ignition is on. The

system will not respond to any input except the door triggers, and

the starter kill relay (if installed) will not be activated. Once you

have arrived at your destination, the system will disarm when the

ignition is turned off. The siren will chirp twice and the LED will

then stop flashing. The system can also be disarmed at any time

by pressing 

.

Arming While Driving

Summary of Contents for 6500ESP






































Reviews: