DEI 6000 ESP Owner'S Manual Download

Page: 7 / 40

1999 Directed Electronics, Inc.

What is Included

■

3-Channel Receiver

■

A pair of four-button transmitters

■

A Stinger

Doubleguard

dual-output shock sensor

■

The Revenger

Soft Chirp

six-tone programmable siren

■

The red status LED indicator light

■

A push-button Valet

switch

■

Your warranty card

■

Failsafe

Starter Kill ready circuitry (may require additional

labor)

Important Information

Congratulations on the purchase of your state-of-the-art vehicle

security system. This system has been designed to provide years of

trouble-free operation. Due to the complexity of this system, it

must be installed by an authorized dealer only. Installation of this

product by anyone other than an authorized dealer voids the war-

ranty. All dealers are provided with preprinted dealer certificates to

verify that they are authorized.

This owner’s guide should help you to get the most out of your

system. Please take the time to read it prior to using the system.

Summary of Contents for 6000 ESP









































Search results

Summary of Contents for 6000 ESP

Reviews:

Related manuals for 6000 ESP

Brands by name

Popular brands

DEI 6000 ESP, Owner'S Manual

Search results

Summary of Contents for 6000 ESP

Reviews:

Related manuals for 6000 ESP

Brands by name

Popular brands