background image

31

©

1999 Directed Electronics, Inc.

Power Trunk Release: 

The channel two output of the system can

operate a factory power release for the vehicle’s trunk or hatch.

(An optional relay may be required.) If the factory release is not

power activated, then DEI's 522T trunk release solenoid can often

be added.

Power Window Control: 

Automatic power window control is pro-

vided with the 529T and 530T systems. 

Valet

®

Start System: 

For the ultimate in convenience, the Valet

®

start system can start your vehicle, monitor engine functions, and

power your climate control system with a push of a button! Over-

rev protection, open-hood lockout, brake pedal shutoff, and

automatic timer shutoff are all included. (This feature is only for

automatic transmission, fuel-injected gasoline vehicles.)

820T Valet

®

Car

Com

The 820T Valet

®

Car

Com

is a one-way

pager system that can be added to any compatible DEI security

system. Using the 820T, many of the security and convenience fea-

tures of your DEI security system can be operated from any touch-

tone telephone.

Summary of Contents for 6000 ESP









































Reviews: