DEHOUST AQF 570/5 Operating And Installation Manual Download Page 15

Page: 15 / 16

DEHOUST GMBH – GUTENBERGSTR. 5-7 – D-69181 LEIMEN – www.dehoust.com

7.2.1. Slide ring seal/bearing of immersion pressure pump

An exchange of the slide ring seal is recommended after 10,000 hours of operation or after 10 years whichever is sooner. In case
of early wear and tear, the slide ring seal should also be replaced.

7.2.2. Removal of the immersion pressure pump

The immersion pressure pump is connected in the inside of the tank through an electrical plug connection. When it is necessary

to remove the immersion pressure pump, the electrical plug connection can be disconnected and the immersion pressure pump

can be removed. The pressure hose must be removed by disconnecting the hose clip from the hose socket.

Electrical plug connector - PIN assignment of immersion pressure pump: 1; 3; PE

Summary of Contents for AQF 570/5

















Search results

Summary of Contents for AQF 570/5

Reviews:

Related manuals for AQF 570/5

Brands by name

Popular brands

DEHOUST AQF 570/5, Operating And Installation Manual

Search results

Summary of Contents for AQF 570/5

Reviews:

Related manuals for AQF 570/5

Brands by name

Popular brands