DEEP SEA ELECTRONICS DSECONTROL DSE7000 Series Operator'S Manual Download Page 19

Page: 19 / 78

DSE Model 7000 Series Control & Instrumentation System Operators Manual

Part No. 057-074 7000 Series OPERATING MANUAL ISSUE 2 02/05/2008 ADM

4.2 TERMINAL DESCRIPTION

4.2.1 DC SUPPLY, FUEL AND START OUTPUTS

PIN

DESCRIPTION

CABLE

SIZE

NOTES

DC Plant Supply Input
(Negative)

2.5mm²

AWG 13

DC Plant Supply Input
(Positive)

2.5 mm²

AWG 13

(Recommended Maximum Fuse 15A anti-surge)
Supplies the module (2A anti-surge requirement) and Output
relays E,F,G & H

Emergency Stop Input

2.5mm²

AWG 13

Plant Supply Positive. Also supplies outputs 1 & 2.
(Recommended Maximum Fuse 20A)

Output relay A (FUEL)

2.5mm²

AWG 13

Plant Supply Positive from terminal 3. 15 Amp rated.
Fixed as FUEL relay if electronic engine is not configured.

Output relay B (START)

2.5mm²

AWG 13

Plant Supply Positive from terminal 3. 15 Amp rated.
Fixed as START relay if electronic engine is not configured.

Charge fail / excite

2.5mm²

AWG 13

Do not connect to ground (battery negative).
If charge alternator is not fitted, leave this terminal
disconnected.

Functional Earth

2.5mm²

AWG 13

Connect to a good clean earth point.

Output relay E

1.0mm²

AWG 18

Plant Supply Positive from terminal 2. 3 Amp rated.

Output relay F

1.0mm²

AWG 18

Plant Supply Positive from terminal 2. 3 Amp rated.

Output relay G

1.0mm²

AWG 18

Plant Supply Positive. from terminal 2. 3 Amp rated.

Output relay H

1.0mm²

AWG 18

Plant Supply Positive from terminal 2. 3 Amp rated.

NOTE:- Terminals 12 to 14 are not fitted to the DSE7200/DSE7300 series controller.

NOTE:- When the module is configured for operation with an electronic engine, FUEL and START

output requirements may be different. Refer to Electronic Engines and DSE Wiring for further information.
Part No. 057-004.

4.2.2 ANALOGUE SENSOR

PIN

DESCRIPTION

CABLE

SIZE

NOTES

Sensor Common Return

0.5mm²

AWG 20

Return feed for sensors*

Oil Pressure Input

0.5mm²

AWG 20

Connect to Oil pressure sensor

Coolant Temperature Input

0.5mm²

AWG 20

Connect to Coolant Temperature sensor

Fuel Level input

0.5mm²

AWG 20

Connect to Fuel Level sensor

Flexible sensor
(not available on 7200 series controller)

0.5mm²

AWG 20

Connect to additional sensor (user configurable)

NOTE:- Terminals 20 and 21 are not fitted to the 7200/7300 series controller.

NOTE*:- If using single terminal sensors refer to the Appendix section entitled “Sensor wiring

recommendations” elsewhere in this manual.

Summary of Contents for DSECONTROL DSE7000 Series















































































Search results

Summary of Contents for DSECONTROL DSE7000 Series

Reviews:

Brands by name

Popular brands

DEEP SEA ELECTRONICS DSECONTROL DSE7000 Series, Operator'S Manual

Search results

Summary of Contents for DSECONTROL DSE7000 Series

Reviews:

Brands by name

Popular brands