DEC a-Series Installation And Setup Manual Download Page 37

Page: 37 / 44

Troubleshooting

Installation and Setup Guide 3–9

Table 3-2: Disk Drive Troubleshooting

Problem

Possible Cause

Action

Hard disk drive cannot read
or write information.

Incorrect SCSI drive ID
settings.

Loose or incorrectly
installed cables.

Disk drive is not correctly
formatted or partitioned.

External drive not powered
up.

Set the SCSI ID.
Refer to the disk drive installation
instructions.

Make sure all cables are correctly
installed.

Format and partition as required using
the supplied operating system.

Turn on the external drive.

Floppy drive cannot read or
write information.

Floppy diskette is not
formatted.

Floppy diskette is wrong
density.

Floppy diskette is worn or
damaged.

Floppy diskette is write
protected.

Floppy drive is empty.

Floppy drive power or data
cable not connected.

Floppy drive data cable
connector installed
backwards.

Format the floppy diskette.

Use a floppy diskette of the proper
density for your drive.

Try another floppy diskette.

Slide the write-protect switch so the
hole is not visible.

Insert a floppy diskette.

Connect floppy drive power or data
cable.

Install floppy drive data cable
connector correctly.

Summary of Contents for a-Series













































Search results

Summary of Contents for a-Series

Reviews:

Related manuals for a-Series

Brands by name

Popular brands

DEC a-Series, Installation And Setup Manual

Search results

Summary of Contents for a-Series

Reviews:

Related manuals for a-Series

Brands by name

Popular brands