Dean 1824 Installation & Operation Manual Download | Manualshive

Page: 41 / 46

background image

24G SERIES FLATBOTTOM GAS FRYERS

CHAPTER 6: PREVENTATIVE MAINTENANCE

6-3

6.1.4 Stainless Steel Care

WARNING

DO NOT let water splash into the tank of hot oil. It will splatter and can cause severe

burns.

All stainless steel fryer cabinet parts should be wiped regularly with hot, soapy water during the day,
and with a liquid cleanser designed for stainless steel at the end of each day.

A. Do not use steel wool, abrasive cloths, cleansers or powders.

B. Do not use a metal knife, spatula or any other metal tool to scrape stainless steel! Scratches

are almost impossible to remove.

C. If it is necessary to scrape the stainless steel to remove any encrusted materials, soak the area

first to soften the deposit, then use a wood or nylon scraper only.

«
...
39
40
41
42
43
...
»

Summary of Contents for 1824















































Reviews:

No comments

Related manuals for 1824

Brand: Livoo Pages: 9

Brand: Linea 2000 Pages: 50

Brand: Parker Pages: 100

Brand: aeolus Pages: 2

Brand: TriStar Pages: 14

Brand: T-Fal Pages: 24

Brand: T-Fal Pages: 28

P/N 134296400A (0404)

Brand: Frigidaire Pages: 9

Brand: Frigidaire Pages: 2

Stackable Dryer

Brand: Frigidaire Pages: 27

Brand: Parker Pages: 129

Brand: Bosch Pages: 28

Brand: Bosch Pages: 8

Brand: Bosch Pages: 8

Brand: Bosch Pages: 8

Brand: Bosch Pages: 32

Brand: Bosch Pages: 40

Brand: Bosch Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands