background image

Http://www.dbltek.com 

VP-102 / VP-202 User Manual 

20 

 

 

 

3.

 

PPPoE

 – This selection is intended for broadband connection (ADSL / Cable modem) that requires dial up / 

authentication using PPPoE protocol.  Both 

User Name

 and 

Password 

are required.  Please consult your 

service provider for more information if needed.  One advantage with the PPPoE dial up is that the IP 
address obtained for the LAN port is normally a public IP. 

 

More advanced parameters for 

802.1q VLAN

 and 

MAC

 settings are available.  Please consult your network 

administrator for assistance if needed. 

 

PC PORT 

– The PC port is intended to provide an Ethernet connection to other network devices (for example: 

PC, network HUB.).  Two modes of operation are available: 

 
1.

 

Bridge mode 

- This mode allows the network traffics at the PC port to be bypassed to LAN port.  This 

means that the network device share the same network segment as the LAN port.  There is no IP address 
assigned to the PC port. 

2.

 

Fixed IP 

- This mode sets the PC port 

IP Addresss

 (private IP) and 

Subnet Mask

 manually.  This creates 

a new network segment for the network devices connected to the PC Port.   

 

To simplify network IP assignments, enable the DHCP Server for the PC Port.  This allows network 
devices connected Port to obtain network IP and related information from the PC Port.  Please consult your 
network administrator for proper settings of the DHCP Server 

Summary of Contents for VP-102













































Reviews: