DBL Technology GoIP User Manual Download Page 45

Page: 45 / 63

GoIP User Manual

http://www.dbltek.com

3.3.14 SMS

This page covers parameters that are related to SMS.

The top parameter (SMS to VoIP) is a general setting for all

channels.

This defines how received SMS messages are used for Call Back or Forward functions which are

described in details in the table below.

Parameter

Description

Default Value

SMS to VoIP



Call Mode



Dialing Prefix



VoIP Number



GSM Number

This defines how the device handles received SMS messages.

Call Function – This mode is used to support Call Back function via

incoming GSM messages.

Appendix B describes the three different

modes of operations in order to meet the different requirements from
various SIP servers.

Please note that the SIP server registered must be

configured for this operation.

This parameter specify which SMS Dial mode is used.

Please refer to

Appendix B for more information on the modes available.

The parameter is applicable for SMS Dial mode.

It allows a prefix to be

added to the phone number of the called party.

Forward Function – This mode forwards incoming GSM SMS to a SIP

terminal and a GSM number.

Incoming GSM messages (SMS) received are forwarded to the SIP Phone
Number specified in this parameter.
Incoming GSM messages (SMS) received are forwarded to the GSM Phone
Number specified in this parameter.

The channel received the message is

used to forward the message.

Disabled

Summary of Contents for GoIP
































































Search results

Summary of Contents for GoIP

Reviews:

Related manuals for GoIP

Brands by name

Popular brands

DBL Technology GoIP, User Manual

Search results

Summary of Contents for GoIP

Reviews:

Related manuals for GoIP

Brands by name

Popular brands