MAINS LINK
MAINS FUSES
220-240V~ 50-60Hz 6A
100-120V~ 50-60Hz 12A
220-240V~ (10Amax) 2300Wmax
100-120V~ (3Amax) 330Wmax
(REPLACE FUSE WITH SAME RATINGS)
(REMPLACER LE FUSIBLE AVEC LE MÊME TYPE)
0 0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
[ms]
4.5
DELAY
POLARITY
180°
0°
READY
LIMITER
SIGNAL
MUTE/PROT
BALANCED
INPUTS
BALANCED
OUTPUTS
120Hz
90Hz
Link
Xover
SUBWOOFER
SETUP
SERVICE
DATA
XOVER
OUTPUTS
MODE
100-120V~ (T8A L 250V~)
220-240V~ (T4A L 250V~)
AUTO-RANGE
MAINS INPUT
“CAUTION”
RISK OF ELECTRICAL SHOCK
DO NOT OPEN
“ATTENTION”
RISQUE DE CHOCH ELECTRIQUE
NE PAS OUVRIR
Se
ri
al
N
.
Made in China
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference,
and (2) this device must accept any interference
received, including interference that may cause
undesired operation.
TECHNOLOGIES
8
0dB
MONO
0dB
STEREO
OUT 2
OUT 1
INPUT 2
INPUT 1
DESIGNED & DEVELOPED
IN ITALY
SUBWOOFER
LEVEL
AEB INDUSTRIALE S.R.L.
Via Brodolini, 8
Località Crespellano
40053 VALSAMOGGIA (BO)
ITALY
0 0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
[ms]
4.5
DELAY
POLARITY
180°
0°
READY
LIMITER
SIGNAL
MUTE/PROT
BALANCED
INPUTS
BALANCED
OUTPUTS
120Hz
90Hz
Link
Xover
SUBWOOFER
SETUP
SERVICE
DATA
XOVER
OUTPUTS
MODE
8
0dB
MONO
0dB
STEREO
OUT 2
OUT 1
INPUT 2
INPUT 1
SUBWOOFER
LEVEL
MAINS LINK
MAINS FUSES
220-240V~ 50-60Hz 6A
100-120V~ 50-60Hz 12A
220-240V~ (10Amax) 2300Wmax
100-120V~ (3Amax) 330Wmax
(REPLACE FUSE WITH SAME RATINGS)
(REMPLACER LE FUSIBLE AVEC LE MÊME TYPE)
100-120V~ (T8A L 250V~)
220-240V~ (T4A L 250V~)
AUTO-RANGE
MAINS INPUT
23
SIGMA S218
Cod. 420120258 REV. 1.0
FEATURES OF THE AMPLIFIER AND CONTROL SECTIONS
DIGIPRO G3 amplifier is at the heart of SIGMA S218.
The system is silent and is controlled by a dedicated
DSP that manages the different parameters.
The sound amplification power is 1800 W RMS.
The amplifier panel is made up of:
WARNING
!
•
Input, Output and Control Section
•
Power Supply Unit Section
•
Never attempt to disassemble the amplifier
in any way.
•
In case of overheating, the audio volume
is gradually reduced until module thermal
stabilization. The level is automatically
restored when the correct operating
temperature is reached.
•
In the event of a malfunction, immediately
cut power supply off, by disconnecting the
module from the mains, and contact an
authorised repair centre.
•
The fuse installed at the factory is rated for
operation in the 220-240 V voltage range. If
you need to operate the speaker in the 100-
120V~ range:
1. Disconnect all connections,
including the power supply
connection.
2. Wait 5 minutes.
3. Replace the fuse with the fuse
rated for the 100-120 V range,
which is included in the package.
POWER SUPPL
Y UN
IT SECTION
IN
PUT
, OUTPUT AN
D CONTROL SECTION
•
Never remove the front grille protecting
the product. To prevent electric shock,
in case of protection grille accidental
damage or replacement (to be carried out
at the after-sales service), immediately
disconnect power supply. Never connect
mains power supply when the grille is
removed.
WARNING
!
