background image

The Rome Electric Bicycle User’s Guide 

TPS Training Bulletin 

Page 16

 

Technical Data 

This section provides you with the technical specifications for your e-bike. 

The Motor and Wheel Assembly 

The Rome e-bike has a 500 Watt magnetic DC brushless motor on the rear wheel hub. 
This type of motor has excellent low-end torque and high efficiency when working within its 
range. Note that while the motor is very quiet, it does produce some noise. Also attached to 
the rear hub are speed reduction gear and the speed free clutch. 

The Freewheel 

The wheels have freewheels, so the e-bike’s drive train is not fixedly geared. This means 
that when coasting or traveling downhill, you can turn off the engine and your e-bike will 
continue to move without slowing. This feature will allow you to achieve faster speeds 
when coasting, moving downhill or moving with the wind. It will also allow you to conserve 
electrical power, because you will be able to let to the motor rest while moving. 

The Controller 

Daymak pioneered the development of intelligent component control in e-bikes. The “D-
Drive” technology developed by Daymak is the brain of your e-bike. It allows your e-bike to 
achieve faster acceleration, to climb steeper hills, and to save energy. In future, it will allow 
for other ways of recharging your e-bike’s batteries, such as by using solar or wind power. 
 
The electronic controller is located under the seat assembly. This controller efficiently 
regulates the speed and electronic functions of the bicycle. It allows for stepless speed 
adjustment, shuts off the motor when the brakes are activated, has low voltage protection 
and has fuses to prevent excess current from damaging the e-bike’s systems. 

The Governor 

A key component of the controller is the Governor. The Governor regulates the speed of 
the e-bike. It prevents the motor from assisting riders when the e-bike’s speed surpasses 
32 km per hour. 
 

Note     

The governor’s primary function is to make sure that the motor functions efficiently. If 
the governor is not functioning, the mileage of the e-bike will be dramatically reduced, 
and its performance will suffer. 
 
Disabling the governor voids the warranty, and may damage your controller. 

 
This speed limitation to 32 km per hour is required by government regulations. Traveling 
faster than 32 km per hour through motor power alone is illegal in Canada and could result 
in serious fines or penalties, unless your vehicle is insured for liability, is registered and you 
are licensed to drive. 

 

Summary of Contents for The Rome E-Bike


























Reviews: