DAXOM UKDAX-11ST Installation & Operation Manual Download Page 3

 

Thanks  to  its  feature  of  digital  constant  water  setting,  the  water 

temperature will remain constant in the degree you set. 

The  fuel  efficiency  is    reduced  in  low  water  temperature  as  your 

device can operate in the desired constant water temperatures.  

By  the  automatic  water  controlled  on/off  system,  when  the  water 

valve is opened, the water heater will be ignite automatically and the 

hot water flow will be provided.  When the water valve is closed, the 

water flow will stop and the flame will be off automatically.   

Thanks  to  its  feature of  operating  with  low  pressure  water,  it  will  not 

be  affected  by  the  low  water  pressure  that  occurs  in  the  high 

apartment flats. 2 mSS 

The  temperature  control  adjustment  buttons  make  for  users  easy  to 

obtain different water temperature that they desire.  

By  the  high  pressure  safety  system,  when  the  water  pressure  is 

higher than it’s needed, safety valve will discharge the excess water 

by become a part of a activity. 

 By the high temperature safety system, in case of  the water getting 

hotter than it is needed, the gas will be cut off automatically and the 

damage of the water heater will be prevented.  

The  flame  instability  is  prevented  and  the  water  is  cooled  after  the 

flame is off with the features of blowing inside the water heater before 

the ignition (air fan blows air for 2~4 seconds before ignition) and the 

blowing  after  service  (air  fan  will  go  on  blowing  air  for  10  seconds 

after the water stops and the flame is off). 

Thanks to the safe and reliable design of the combustion system, the 

air is taken from outside by the fan for the purpose of the combustion 

and it is sent out again after the combustion.  

By  the  system  of  continuous    electronic  ignition,  100%  success  is 

achieved in ignition.  

The device is equipped with the multi-purpose safety system. Even if 

the  power  is  supplied to  the water  heater again  in  power  failure,  fan 

failure,  the  blocking  of  the  waste  gas  pipe  or  strong  reverse  wind 

blowing  the  gas  will  be  automatically  cut  and  the  automatic  ignition 

system will be disabled. In this case the water heater will need to be 

restarted.  

1.  THE  FEATURES  AND  THE  CHARACTERISTICS  OF 

YOUR WATER HEATER  

Summary of Contents for UKDAX-11ST

















Reviews: