DAVIS Vantage Pro ISS Retrofit Kit Instructions Manual Download Page 8 | Manualshive

Page: 8 / 8

DAVIS Vantage Pro ISS Retrofit Kit Instructions Manual Download Page 8

Product Numbers: 6920, 6920C

Davis Instruments Part Number: 7395.307
ISS Retrofit Kit
Rev. B Manual (02/19/03)

This product complies with the essential protection requirements of the EC EMC Directve 89/336/EC.
Copyright ©2003 Davis Instruments Corp. All rights reserved.

Vantage Pro is a registered trademark of Davis Instruments Corporation.

3465 Diablo Avenue, Hayward, CA 94545-2778 U.S.A.

510-732-9229 • Fax: 510-732-9188

E-mail: [email protected] • www.davisnet.com

FCC Part 15 Class B Registration Warning

This equipment has been tested and found to comply with the limits for a class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved in writing by Davis Instruments may void
the user’s authority to operate this equipment.

3.

Ship to:

Davis Instruments
Attn: Returns
3465 Diablo Ave.
Hayward, CA 94545

Troubleshooting

Please contact Davis Technical Support if you have any questions or problems
installing the ISS Retrofit Kit.

Contacting Davis Technical Support

(510) 732-7814

for Technical Support, Monday – Friday, 7:00 a.m. – 5:30 p.m.

Pacific Time.

(510) 670-0589

Fax to Technical Support.

[email protected]

E-mail to Technical Support.

www.davisnet.com

Copies of User Manuals are available from the Weather

Support page. Watch for FAQs and updates. Subscribe to the e-newsletter.

ISS2 RetroKit D011.fm Page 8 Wednesday, February 19, 2003 6:02 PM

«
...
6
7
8

Summary of Contents for Vantage Pro ISS Retrofit Kit









Reviews:

No comments