manualshive.com logo in svg

DAVIS Vantage Pro ISS Retrofit Kit, Instructions Manual, Page: 5 / 8

Share
Download
DAVIS Vantage Pro ISS Retrofit Kit Instructions Manual Download Page 5

Install the Retrofit Kit Components

Page 5

Install the Retrofit Kit Components

1.

Open the SIM housing cover.  Note the “S-loop” in which the TEMP-HUM 
cable is formed.  

2.

Disconnect the TEMP-HUM cable and close the SIM housing cover.

3.

Place the new SIM housing, radiation sensor plate and Temp/Hum sensor 
assembly on the work surface with the SIM housing on the bottom. 

4.

Place the two open plates on the Assembly, feeding the TEMP-HUM cable 
through the opening in the plates.  Be sure that the three screw holes line 
up.

Use your thumbs to push 
back on the two (2) plastic 
latches.

Screw Fastening Holes. 
Use self-threading screws:
#6 x 0.5" (3.5mm x 12 mm)
(optional)

With the latches pushed
back, use your fingers to 
lift up on the corner edges 
of the cover.

SIM Housing

SIM Housing Cover

1

2

Opening the SIM Housing Cover

Cable Routing Channels

(press cables fully into channel

to form "S-loop")

DIP Switches

(wireless models

only)

Console Cable

(cabled models

only)

Solar Panel Power

(wireless models only)

AC Power
(optional)

3-Volt Lithium Battery
(wireless models only)

UV Sensor

Optional

Solar Radiation

Rain Collector

Anemometer

Temp/Humidity

New SIM Connections

ISS2 RetroKit D011.fm  Page 5  Wednesday, February 19, 2003  6:02 PM

Summary of Contents for Vantage Pro ISS Retrofit Kit









Reviews:

No comments