DAVIS Vantage Pro ISS Retrofit Kit Instructions Manual Download Page 6 | Manualshive

Page: 6 / 8

DAVIS Vantage Pro ISS Retrofit Kit Instructions Manual Download Page 6

Page 6

Vantage Pro® ISS Retrofit Kit

5.

Place the top closed
radiation shield plate
that you saved during
disassembly on top of
the stack. The TEMP-
HUM cable should exit
between the upper of
the two open plates
and the top closed
plate, in the direction
towards the SIM hous-
ing cable channels.

6.

Holding the rain col-
lector base above the
stack of plates, place
the SOLAR PANEL cable, if present, across the top of the plates so that it runs
between the top plate and the base, and from the front to back of the base).

7.

Place the rain collector base down on top of the stack of plates.

8.

Insert the 3 screws, with lock washers and flat washers, through the rain col-
lector base and radiation shield plates into the threaded inserts in the bottom
plate (see figure). Use the screws to fasten the radiation shield to the base.

9.

Install the Rain Collector cone.

Connect Cables and Power the New Sim

1.

Turn the assembly upside-down(SIM housing on top) and open the SIM hous-
ing cover.

2.

Plug in the TEMP-HUM sensor and the RAIN cable, and if present, plug in the
solar panel power cable and the SUN and UV sensor cables.

Note:

Be sure to push the cables deep into the cable channels to form S-loops (see figure).

3.

Wireless Models Only: Install the battery. Be careful to observe the battery
polarity markings on the battery holder.

4.

Wireless Models Only: Set the transmitter ID code to match the settings used
on the old SIM.

Note:Make sure the transmitter DIP switch #4 on the new SIM is in the OFF position.

5.

Close the SIM housing cover.

Verify Communications - Wireless Models

1.

If your console is in Setup Mode, you will need to exit Setup Mode to perform
this test. You can exit Setup Mode by pressing and holding the DONE key.

2.

Press and hold the TEMP key and then press TIME key on the console to dis-
play the Diagnostic Screen.

3 3/4 Inch Screw

Lock Washer

Flat Washer

Top Plate

Middle Plates

SIM Housing

Temp/Hum
Sensor

Solar Power
Cable Routing

TEMP-HUM
Cable
Routing

ISS2 RetroKit D011.fm Page 6 Wednesday, February 19, 2003 6:02 PM

«
...
4
5
6
7
8
»

Summary of Contents for Vantage Pro ISS Retrofit Kit









Reviews:

No comments