manualshive.com logo in svg

Datex-Ohmeda M-NMT, Technical Reference Manual Slot

Share
Download
Datex-Ohmeda M-NMT Technical Reference Manual Slot Download Page 17

NeuroMuscular Transmission Module, M-NMT

Document No. 800 1018-1

13

19.

 

Perform an electrical safety check and a leakage current test.

?

20.

 

Check that the module functions normally after performing the electrical safety check.

?

21.

 

Clean the module with suitable detergent.

?

•

 

Fill in all necessary documents.

 

3.3

 

Disassembly and reassembly

Disassemble the NeuroMuscular Transmission Module, M-NMT, in the following way. See the

exploded view of the module.
1.

 

Remove the two screws from the back of the module.

2.

 

Pull the module box slowly rearward and detach it from main body. Be careful with the loose

latch and spring locking pin.

3.

 

Detach the NMT board by removing the two screws located near the front panel frame,

disconnect the cables and pull out the front panel frame.

To reassemble the module, reverse the order of the disassembly steps.

CAUTION

 

When reassembling the module, make sure that the cables are reconnected

properly.

Summary of Contents for M-NMT































Reviews:

No comments

Brands by name

Popular brands

Load more brands