manualshive.com logo in svg

Datex-Ohmeda AS/3 K-ANE, Technical Reference Manual

Share
Download
Datex-Ohmeda AS/3 K-ANE Technical Reference Manual Download Page 8

S/5 Keyboards

Document No. 8001589-1

4

LEDs

The alarm LEDs are activated by the Command Board/Bar PCB under the commands received via

serial communication from the CPU board. The red or yellow alarm LED is lit when red or yellow

alarm is activated. STBY -led is lit when the device is turned to stand-by and connected to mains.
NOTE: If there are two Command Boards/Bars connected to the system, the system is ON (STBY

LED not lit), when at least one of the switches is positioned ON.

2.1.1

 

Connectors and signals

26-pin D-connector on K-ANE/K-ICU and K-ANEB/K-ICUB

Pin No

I/O Signal

1

2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26

I

I
O

O
I

Not connected
Not connected
Not connected
Not connected
Not connected
GND
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected
N ot connected
+5 V
ON/STBY
Not connected
Not connected
TXDD RS232
RXDD RS232
Not connected
Not connected
Not connected
Not connected
Not connected
Not connected

Summary of Contents for AS/3 K-ANE

































Reviews:

No comments

Brands by name

Popular brands

Load more brands