manualshive.com logo in svg

Datex-Ohmeda AS/3 K-ANE, Technical Reference Manual

Share
Download
Datex-Ohmeda AS/3 K-ANE Technical Reference Manual Download Page 7

Command Boards / Bars, Remote Controller

Document No. 8001589 -1

3

2

 

FUNCTIONAL DESCRIPTION

2.1

 

Command Boards, K-ANE/K-ICU and Command Bars, K-ANEB/ K-ICUB

CPU

PROGRAM
MEMORY
EPROM

KEYBOARD
SCANNING
CIRCUIT

ALARM
LEDS

KEYBOARD

COMWHEEL

5 PIN DIN

(D-LCC10)

CONNECTOR

ON/STBY
SWITCH

STBY
LED

RS-232

X5

X4

X1

X2

KEYBOARD PCB

DISPLAY
CONTROLLER
BOARD

DISPLAY
CONTROLLER
BOARD

Figure 1

K-ANE/ K-ICU and K-ANEB/K-ICUB block diagram

K-ANE/ K-ICU, K-ANEB/K-ICUB

The Command board/bar consists of 17 direct function keys, ComWheel and ON/STBY switch.

Command Board/Bar PCB

The PCB is located inside the Command Board/Bar.The board reads the status of the front panel

keys and the ComWheel and forwards the information to the CPU board.

External communication

Communication with the host processor takes place in RS232 serial communication channels

which are available in both the CPU bus and the module bus. Two signals, TXD and RXD, are in use.

No handshaking is used. The 26-pin subminiature D-connector of the Command Board/Bar is
connected to a Display controller board. Serial communication speed rate is 19.2 kbps.

ComWheel

The ComWheel on the front panel is used for menu selection.

Summary of Contents for AS/3 K-ANE

































Reviews:

No comments

Brands by name

Popular brands

Load more brands