background image

    

 

 

XM-DVR Pro

 Dual Channel DVR                                          Page 29 of 32 

December 2009                                                                 Manual Rev 3.05 

Trouble Shooting

  

 

The DVR is equipped with three 

status lights: 

 

Power – Green 

 

Fault – Red 

 

Active – Amber 

o

 

Ready:

    

Slow Blink, 1500ms/ 

o

 

Recording:

  

Fast Blink, 500ms/ 

 

These status lights will indicate DVR status and function. 

 

 

Indication – No lights are lit. 

o

 

Problem – Inadequate power is being supplied to the DVR 

 

Possible solutions 

 

Make sure power supply is on 

 

Check ground and power connection 

 

Check cabling for shorts 

 

Indication – Only the 

Green Power

 light it lit. 

o

 

Problem – Unit is not booting 

 

Possible Solutions 

 

Ensure the DVR is being supplied adequate 
power 

 

Power down and re-insert card 

 

Remove and format CF Card 

 

Replace CF card 

 

Indication – The 

Red

 

Fault

 light is lit. 

o

 

Problem – Time has been reset 

 

Possible Solutions 

 

Set time through on screen menu. Power on unit 
for ~14 hours to charge clock battery 

o

 

Problem – Memory is full 

 

Possible Solutions 

 

Delete Video Events 

o

 

Problem – Media is not properly formatted/inserted 

 

Possible Solutions 

 

Format media to FAT32 

 

Re-insert media 

 

Indication – 

Amber Active

 light continues to blink slowly 

o

 

Problem – DVR is not recording 

 

Possible Solutions 

 

Connect Cameras 

 

Connect Switch 

 

Change Switch Settings 

    

 

 

XM-DVR Pro

 Dual Channel DVR                                          Page 30 of 32 

December 2009                                                                 Manual Rev 3.05 

Accessories 

 

Datatoys offers a wide variety of accessories that can be added to your DVR. 

 

Monitors

 

 
Several monitors are available that can be added to 

your DVR system. Please see 

www.datatoys.com

 for more 

information. 

 

Camera Switchers

 

 
Datatoys offers a four-camera switcher that will allow you to seamlessly switch 

between two to four cameras. Please see 

www.datatoys.com

 for more information. 

 
Picture-in-Picture Processors 

 
The Multi-View Quattro-b Picture-in-Picture processor 

and overlay unit was specifically designed to be paired with 
the DVR system. This unit can overlay speed, altitude, 
accelerometer and GPS coordinates. Please see 

www.datatoys.com

 for more information. 

 

Cabling

 

 
Datatoys offers a wide variety of cabling from double 

shielded extensions to adapter cables. Audio adapter cables 
are available for nearly every communications system and 
standard video adapter cables are available as well. Datatoys 
also makes custom adapters for virtually any application. 
Please see 

www.datatoys.com

 for more information. 

 

Mounts

 

 
Mounts are available for nearly any application. Please see 

www.datatoys.com

 

for more information. 

Summary of Contents for XM-DVR Pro

















Reviews: