background image

DI-2108-P Hardware Manual

Specifications

4

Synchronized Performance

Number of synced units (PC-dependent): 16 units max; Throughput 

 480 kHz

Channel skew between any 2 units: 

10 µS, typical

Setup constraints:

Syncs only with other model DI-2108-P instruments. 
Same number of enabled channels per synced unit (type does not matter)
Same sample throughput rate per synced unit.
All units connected to the same USB controller using one or more hubs. 

Count/Rate

Digital port assignment:

Count: Port 2 configured as input
Rate: Port 3 configured as input

Internal pull-up value:

4.7 k

Input high voltage threshold:

2.4V

Input low voltage threshold:

0.8V

Terminal count:

65,535

Maximum rate frequency:

50 kHz (with total160 kHz burst rate)

Minimum rate frequency:

0.5 Hz

Maximum count frequency:

50 kHz

Removable Memory

Type:

MLC, pSLC, or SLC flash memory (with USB SD card reader); USB
thumb drive

Required Format:

FAT32

Number of Channels:

1; Unlock code required to record 2 or more channels to thumb drive

Indicators and Connections

Interface:

USB 2.0 (mini-B style connector)

Indicator light:

Multi-color LED

USB A Connector (Drive):

USB drive for Stand-alone data logging
Cannot be used concurrently with the USB interface

Input connections:

Two 16-position screw terminal strips

Power

Power Consumption:

<1.0 Watt, via USB interface

Environmental

Operating Temperature:

0°C to 50°C (32°F to 122°F)

Operating Humidity:

0 to 90% non-condensing

Storage Temperature:

-20°C to 60°C (-4°F to 140°F)

Storage Humidity:

0 to 90% non-condensing

Summary of Contents for DI-2108-P











































Reviews: