background image

 

ORIGINAL INSTRUCTIONS (ref. 2006/42/EC) 

This product is covered by one or more of the following patents. 

Italian Patent IT 1,363,719              Additional patents pending 

 
 
 

 

CE Compliance 

 
CE marking states the compliance of the product with essential requirements listed in the applicable European directive. Since 
the directives and applicable standards are subject to continuous updates, and since Datalogic promptly adopts these updates, 
therefore the EU declaration of conformity is a living document. The EU declaration of conformity is available for competent 
authorities and customers through Datalogic commercial reference contacts. Since April 20th, 2016 the main European 
directives applicable to Datalogic products require inclusion of an adequate analysis and assessment of the risk(s). This 
evaluation was carried out in relation to the applicable points of the standards listed in the Declaration of Conformity. Datalogic 
products are mainly designed for integration purposes into more complex systems. For this reason it is under the responsibility 
of the system integrator to do a new risk assessment regarding the final installation. 
 

Warning:

 This is a Class A product. In a domestic environment this product may cause radio interference in which case the 

user may be required to take adequate measures. 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

Datalogic S.r.l. 

Via S. Vitalino 13 - 40012 Calderara di Reno - Italy 
Tel: +39 051 3147011 - Fax: +39 051 3147205 - www.datalogic.com

 

 
Helpful links at www.datalogic.com: 

Contact Us,

 

Terms and Conditions,

 

Support

 
The warranty period for this product is 36 months. See General Terms and Conditions of Sales for further details. 
 

 

Under current Italian and European laws, Datalogic is not obliged to take care of product disposal at the end of its 
life. Datalogic recommends disposing of the product in compliance with local laws or contacting authorised waste 
collection centres. 

 
© 2011 - 2017 Datalogic S.p.A. and/or its affiliates 

 ALL RIGHTS RESERVED. 

 Without limiting the rights under 

copyright, no part of this documentation may be reproduced, stored in or introduced into a retrieval system, or transmitted 
in any form or by any means, or for any purpose, without the express written permission of Datalogic S.p.A. and/or its 
affiliates. Datalogic and the Datalogic logo are registered trademarks of Datalogic S.p.A. in many countries, including the 
U.S.A. and the E.U. All other trademarks and brands are property of their respective owners. Datalogic reserves the right 
to make modifications and improvements without prior notification. 

 

821002003 Rev. C 

Summary of Contents for SG2 M Series








Reviews: