background image

DS1500 

 

TROUBLESHOOTING GUIDE 

Problem

 

Suggestions

 

Power On

the “Power On” LED 
is not lit 

Is power connected? 
If using a power adapter (like PG 220), is it connected to a 
wall outlet? 
If using rail power, does rail have power? 
Measure voltage at pin 1 and pin 5. 
 

On line Mode

EXT TRIG LED is 
not lit (when external 
trigger activates) 

Is sensor connected to EXT TRIG pins (9 and 5 for 15-pin 
connector)? 
Is power supplied to photo sensor? 
Are the photo sensor LEDS (if any) working correctly? 
Is the sensor/reflector system aligned? 
 

On line Mode

EXT TRIG LED is 
correctly lit but 
nothing happens (no 
reading results)

 

Is the software configuration consistent with the application 
condition (operating mode etc.)? 
In the WinHost program select the OPERATING MODE 
tab and check for related parameters 
 

Serial On line 
Mode

the reader is not 
triggered (no reading 
results) 

In the WinHost program select the OPERATING MODE 
tab and check if serial on line is enabled as operating 
mode 
Are the Start – Stop characters correctly assigned? 
Is the serial trigger source correctly connected and 
configured? 
 

On line Mode and 
Serial On Line

:

 

Reader doesn’t 
respond correctly to 
the expected 
external signals end 

In the WinHost program select the OPERATING MODE 
tab and check the TIMEOUT parameterization. 
 

 
 
 

38

 

 

 

Summary of Contents for DS1500


































































Reviews: