DASS Tech DASS 3.0i LV Manual For Use And Installation Download Page 60

Page: 60 / 70

DASS 3.0i LV (DSP-123i-ODS)

User manual

- 55 -

temperature.

Env

temp is too high

ID65

UnrecoverHwAc

OCP

The grid current is

too high,and has

cause

unrecoverable

hardware fault

ID65-ID70 are internal faults of inverter,

turn OFF the “DC switch”, wait for 5 minutes,

then turn ON the “DC switch”. Check whether

the fault is rectified. If no, please contact

technical support.

ID66 UnrecoverBusOV

The bus voltage is

too high,and has

cause

unrecoverable fault

ID67 UnrecoverIacRms

Unbalance

The grid current is

unbalance,and has

cause

unrecoverable fault

ID68 UnrecoverIpvUnb

alance

The input current is

unbalance,and has

cause

unrecoverable fault

ID69

UnrecoverVbusU

nbalance

The bus voltage is

unbalance,and has

cause

unrecoverable fault

ID70

Unrecover OCP

Instant

The grid current is

too high,and has

cause

unrecoverable fault

ID71 UnrecoverPvConf

igSetWrong

Incorrect input

mode

Check the input mode(parallel mode/

independent mode) setting of inverter according

to Section 6.3 (C) 6.Input Mode of this user

manual, If it’s incorrect, change it according to

Section 6.3 (A) 10.Set Input mode of this manual

ID74 UnrecoverIPVInst

ant

The input current is

too high,and has

cause

unrecoverable fault

ID74-ID77 are internal faults of inverter,

turn OFF the “DC switch”, wait for 5 minutes,

then turn ON the “DC switch”. Check whether

the fault is rectified. If no, please contact

technical support.

ID75

UnrecoverWRIT

EEEPROM

The EEPROM is

unrecoverable

ID76

UnrecoverREAD

EEPROM

The EEPROM is

unrecoverable

ID77

Unrecover Relay

Fail

Relay has happen

permanent fault

ID81

Over Temp

Derating

The inverter has

derated because of

the temperature is

too high

Ensure the installation position and

installation method meet the requirements of

Section 3.4 of this user manual.Check whether

the ambient temperature of the installation

position exceeds the upper limit. If yes, improve

ventilation to decrease the temperature.

ID82

Over Freq

Derating

The inverter has

derated because of

Inverter automatically reduce the output

power when the frequency of electrical grid is

Summary of Contents for DASS 3.0i LV







































































Search results

Summary of Contents for DASS 3.0i LV

Reviews:

Brands by name

Popular brands

DASS Tech DASS 3.0i LV, Manual For Use And Installation

Search results

Summary of Contents for DASS 3.0i LV

Reviews:

Brands by name

Popular brands