DASS Tech DASS 3.0i LV Manual For Use And Installation Download Page 15

Page: 15 / 70

DASS 3.0i LV (DSP-123i-ODS)

User manual

- 10 -

3. Installation

Outlines of this chapter

This topic describes how to install the DASS 3.0i LV (DSP-123i-ODS) .

Installation notes

3.1. Installation Process

Figure3-1 Installation flowchart

3.2. Checking Before Installation

Checking Outer Packing Materials

Do NOT install the DASS 3.0i LV (DSP-123i-ODS) on

flammable material.

Do NOT install the DASS 3.0i LV (DSP-123i-ODS) in an area

used to store Flammable or explosive material.

Danger

The enclosure and heat sink are very hot while the inverter is

working, therefore do NOT install the DASS 3.0i LV

(DSP-123i-ODS) in places where you might touch them

inadvertently.

Caution

Consider the weight of DASS 3.0i LV (DSP-123i-ODS) when

transporting and moving the inverters.

Choose an appropriate mounting position and surface.

Assign at least two persons to install the inverter.

Attention

Start

Check before
installation

Prepare installation
tools

Determine the
installation

Moving

the

inverter

Install

the

rear

panel

Install

the

inverter

End

Summary of Contents for DASS 3.0i LV







































































Search results

Summary of Contents for DASS 3.0i LV

Reviews:

Related manuals for DASS 3.0i LV

Brands by name

Popular brands

DASS Tech DASS 3.0i LV, Manual For Use And Installation

Search results

Summary of Contents for DASS 3.0i LV

Reviews:

Related manuals for DASS 3.0i LV

Brands by name

Popular brands