g
eneral
safety
regulations
Thank you for having chosen this product. Your new electro-
mechanical barrier has been produced to a high level of quality
and reliability that guarantees efficiency and safety for a long
period of time. The attachments to this booklet contain all the
necessary information to assemble your barrier and to safeguard
your security.
All our products are constructed according to regulations in force.
During assembly and maintenance operations use only original
spare parts. Avoid accidents by taking the necessary preventative
and prudent actions.
i
Mportant
It is forbidden to carry out any assembly, repair or adjustment
operations by non qualified personnel and all necessary precautions
must be taken to avoid accidents, such as disconnecting the
power supply (including any buffer batteries present). All moving
parts must be fitted with protection guards.
ATTENTION: Any use not foreseen in this instruction manual
and/or any arbitrary modifications made to this product or its
components, frees DASPI from all responsibility for damage or
harm to persons, animals or property.
Keep this manual and the attached technical file of the installation
in a safe place, known to all personnel so it is available for future
use. Dispose of all packaging materials after installation (boxes,
plastic, polystyrene, etc.) according to regulations in force, paying
special attention to plastic bags that can be extremely dangerous
if children are in the vicinity.
Instruct all personnel involved with operating the mechanism
about the commands and safety systems installed on the plant.
This product cannot be installed in an explosive atmosphere.
M
aintenance
Disconnect the power supply before carrying out any maintenance
operations. To correctly maintain the plant where the ELTRA 400
barrier is installed, proceed as follows:
Periodically clean the photocell optics.
Charge qualified personnel to adjust the electronic clutch (see
relative paragraph of the electronic control unit installation
manual).
If any malfunction occurs, notify qualified personnel.
d
eMolition
Demolition must take place according to regulations in force.
Recycled materials must be separated by type (copper, aluminium,
plastic, electrical parts, etc.). No materials considered dangerous
to the handling personnel are present.
d
isMantling
Proceed as follows to dismantle or transport the mechanism to
another location:
Turn off the power supply and disconnect the electrical plant.
Disassemble the control panel and all the components of the
installation.
If some components are damaged or cannot be removed, substitute
the components.
englISH
S
ecurity
diStance
m
ecHaniSm
in
mouVement
d
o
not
inStaLL
tHe
automation
in
pLace
fuLL
of
expLoSiVe
moiStureS
e
Lectric
SHocK
u
Se
tHe
gLoVeS
u
Se
gLaSSeS
for
WeLding
K
eep
tHe
protection
carter
ProDuCt tyPe
The ELTRA 400 barrier has been designed and constructed to
open barrier arms up to 4 meters in length. DASPI does not
assume any responsibility for other use than the intended
use of the ELTRA 400 barrier.
ATTENTION: The ELTRA 400 barrier is not equipped with
a mechanical clutch and therefore when installed must be
connected to a special DASPI control unit or to a control unit
equipped with an electronic clutch.
uSe oF tHe MeCHanISM
Important safety instructions
Attention, for personnel safety it is of vital importance to
carry out the following instructions.
Keep these instructions in a safe place. Do not allow children
to play with the fixed or remote controls of the gate. Place
the remote controls out of the reach of children.
As the mechanism can be controlled nearby or at a distance
using push buttons or remote controls it is indispensable
that the efficiency of all safety devices be checked frequently.
We recommend periodical checks (every six months) by
qualified personnel to adjust the electronic clutch. To adjust
this protection device, see the paragraph “Electronic clutch
adjustment" in the instruction manual of the electronic
control unit.
PrelIMInary CHeCkS
• Read carefully all parts of this manual.
• Check that the product was not damaged during
transportation.
• Check that the electrical plant conforms to the characteristics
required by the gear motor.
• Check that an adequate grounding plant exists and that all
metallic parts are connected to this plant.
• We remind you that the mechanism facilitates use of the
barrier and does not resolve problems due to defects, bad
installation or lack of maintenance to the barrier.
luBrICatIon
The ELTRA 400 barriers are supplied with permanent grease
lubrication
InStallatIon
Important safety instructions for installation.
Warning: A bad installation can cause a great deal of damage
or harm. Scrupulously follow all installation instructions.
ATTENTION: For any reason whatsoever never disassemble
the barrier arm when it is in a horizontal position
ATTENTION: For any reason whatsoever never carry out an
emergency or manual manoeuvre if the barrier arm is not
assembled
ATTENTION: Do not release the motor when it’s working
For correct commissioning of the ELTRA 400 barriers,
proceed as follows:
Locate the point inside the property where the ELTRA 400
barrier will be installed (figure 1).
Construct a solid concrete base with the dimensions
illustrated on figure 1; provide a passage for the sheath “G”
of the power cables and system controls.
Before the concrete sets, position the “Ps” plate (OPTIONAL)
