DARLAS S-300-2 Installation Instructions Manual Download

Page: 1 / 8

DARLAS S-300-2

ODME PRINTER UPGRADE INSTALLATION INSTRUCTIONS.

5, Kimonos Str., 122 44 Egaleo – Athens – Greece.

Telephones: +30-210-5986179, +30-210-5986213, +30-210-5310551, +30-210-5310674, +30-210-5310775

Fax: +30-210-5911161, E-mail:

[email protected]

Internet:

http://www.darlas.gr

Established in Athens-Greece as a Societal Anonym (SA), Reg. No: 16494/01 /B/88/343, Fully Paid Capital: € 58 694.06

Bankers: National Bank of Greece SA, Egaleo Branch (105), IBAN: GR16 0110 1050 0000 1054 7023 795.

Page 1 of

Dear Customer and or Colleague:

!!!…WARNING…!!!

BEFORE YOU START THE PRINTER UPGRADE JOB PLEASE

READ CAREFULLY THE PRESENT INSTRUCTIONS:

At the end of the job you are kindly requested to send us a small e-mail message
at

[email protected]

letting us know the results of this project.

We are wishing you GOOD LUCK…

Very Best Regards
Darlas Electronic Applications
Technical Department
5, Kimonos Str.,
122 44, Egaleo-Athens-Greece
Phones: +30-210-5986179, +30-210-5986213
Fax: +30-210-5911161
e-mail:

[email protected]

http://www.darlas.gr

Consumables Part Numbers and Descriptions.

Part Number

Description

Qty

Per

Pack

Price

In €

PerPack

1 S-ENRG054-P5

RIBBON INK 5PCS ERC09 MK3 VER 2

5 162.30

2 S-ENRG053-P5

PAPER ROLL EPSON 5PCS MK3 VER 2

5 32.46

Summary of Contents for S-300-2









Search results

Summary of Contents for S-300-2

Reviews:

Related manuals for S-300-2

Brands by name

Popular brands

DARLAS S-300-2, Installation Instructions Manual

Search results

Summary of Contents for S-300-2

Reviews:

Related manuals for S-300-2

Brands by name

Popular brands