DAQ DAQ PCI-MIO E Series User Manual Download | Manualshive

Page: 134 / 162

background image

Fax-on-Demand is a 24-hour information retrieval system containing a library of documents on a
wide range of technical information. You can access Fax-on-Demand from a touch-tone
telephone at (512) 418-1111.

You can submit technical support questions to the applications engineering team through e-mail
at the Internet address listed below. Remember to include your name, address, and phone number
so we can contact you with solutions and suggestions.

[email protected]

Fax and Telephone Support

National Instruments has branch offices all over the world. Use the list below to find the technical
support number for your country. If there is no National Instruments office in your country,
contact the source from which you purchased your software to obtain support.

Telephone

Fax

Australia

03 9879 5166

03 9879 6277

Austria

0662 45 79 90 0

0662 45 79 90 19

Belgium

02 757 00 20

02 757 03 11

Canada (Ontario)

905 785 0085

905 785 0086

Canada (Quebec)

514 694 8521

514 694 4399

Denmark

45 76 26 00

45 76 26 02

Finland

09 527 2321

09 502 2930

France

01 48 14 24 24

01 48 14 24 14

Germany

089 741 31 30

089 714 60 35

Hong Kong

2645 3186

2686 8505

Israel

03 5734815

03 5734816

Italy

02 413091

02 41309215

Japan

03 5472 2970

03 5472 2977

Korea

02 596 7456

02 596 7455

Mexico

5 520 2635

5 520 3282

Netherlands

0348 433466

0348 430673

Norway

32 84 84 00

32 84 86 00

Singapore

2265886

2265887

Spain

91 640 0085

91 640 0533

Sweden

08 730 49 70

08 730 43 70

Switzerland

056 200 51 51

056 200 51 55

Taiwan

02 377 1200

02 737 4644

U.K.

01635 523545

01635 523154

Fax-on-Demand Support

E-Mail Support (currently U.S. only)

Click here to comment on this document via

the National Instruments website at

http://www.natinst.com/documentation/daq/

«
...
132
133
134
135
136
...
»

Summary of Contents for DAQ PCI-MIO E Series



































































































































































Reviews:

No comments

Related manuals for DAQ PCI-MIO E Series

Brand: D-Link Pages: 15

Brand: GE Pages: 6

Brand: LORD Pages: 9

nForce 680I LT SLI

Brand: Nvidia Pages: 80

Brand: SIIG Pages: 20

Brand: Atmel Pages: 2

Brand: sound4 Pages: 66

2ND GENERATION CORE PROCESSOR FAMILY DESKTOP - VOLUME 1 01-2011

Brand: Intel Pages: 172

EK-FC670 GTX Series

Brand: ekwb Pages: 2

NVR52A16-16P-4KS2

Brand: Dahua Technology Pages: 13

Wireless G F5D7000

Brand: Belkin Pages: 252

Brand: ADTRAN Pages: 2

Brand: ADTRAN Pages: 2

Brand: ADTRAN Pages: 4

Brand: ADTRAN Pages: 9

Brand: AT&T Pages: 16

Brand: Crestron Pages: 52

X-NUCLEO-53L5A1

Brand: ST Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands