DAPAudio CA-4500 Manual Download Page 8 | Manualshive

Page: 8 / 24

background image

7

Ordercode: D4515

CA-4500

Set Up and Operation

Before plugging the unit in, always make sure that the power supply matches the product specification
voltage. Do not attempt to operate a 120V specification product on 240V power, or vice versa.
Install this device on a flat surface, not bending or curved.
Do not supply power before all components of the system are set up and connected properly.

NORMAL

All 4 outputs function independently.

Fig. 04

«
...
6
7
8
9
10
...
»

Summary of Contents for CA-4500

























Reviews:

No comments

Related manuals for CA-4500

Brand: Bad Cat Pages: 9

Brand: JBL Pages: 74

Brand: Xtant Pages: 19

Brand: Xtant Pages: 2

Brand: XINDAK Pages: 12

Brand: Opus Technologies Pages: 36

Brand: AUO Pages: 44

Brand: CSI Pages: 22

Brand: MERRY Pages: 32

Brand: Crown Pages: 32

Brand: SoundMax Pages: 28

Brand: Taramps Pages: 12

Brand: Alphard Pages: 20

Brand: Audio Note Pages: 16

Brand: ALLNIC AUDIO Pages: 9

Brand: Lightning Audio Pages: 4

Brand: Sonosax Pages: 19

Brand: Omnitronic Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands