background image

4

www.danvex.fi

WARNING!!!

All electrical connections works must be done by local professionals, ac-

cording to relevant provisions to operate, or some loss of life, personal injury, 

property loss may be happen. 

Do please read through the manual before electrical works, avoiding any fault opera-

tion that causing loss of life or property. 

Please contact the supplier or the manufacturer if there are any issues arises that are 

not stated in this manual.

 

 

1 SAFETY AND APPLICATION

1.1 Safety

The dehumidifier meets the specifications and safety requirements of European standards, and 
takes into account the safety of personnel and unit in design and manufacturing.
ln each chapter of this manual, there is safety information, and also clearly pointed out dangerous 
operations. The danger symbol is marked оn the unit as а warning.
The manual provides the best dehumidifier operating experience and procedures, but these 
suggestions are only for guidance and do not assume any personal responsibllity or fulfill local 
safety regulations. When installing and operating the unit, you should keep the notice:

During the installation and operating the unit, you should keep the notice:

•  Follow the description and instructions in this manual to protect the safety of the equipment;
•  Take into account the safety of yourself and others;
•  The unit must bе operated and maintained bу professional technicians;
•  Electrical parts must bе maintained bу authorized electricians;
•  lt is forbidden to install the unit in areas equipped with explosion-proof devices;
•  Before opening any maintenance panel, disconnect the unit from the main power supply;
•  The unit should bе cooled for at least 15 minutes before maintenance;
•  The maintenance panel should bе closed after maintenance;
•  The unit is limited to perform dehumidification under atmospheric pressure;
•  lt is forbidden to use the unit without filter. lf the filter is not installed, the rotor will bе 

contaminated and lose function;

•  lt is prohibited to delete or alter the markings and instructions оn the unit;
•  This manual should bе properly kept;
•  Original spare parts should bе used;
•  Written permission must bе obtained for any adjustments or modifications.

Summary of Contents for AD-800































Reviews: