Danfoss VLT 3006, Product Manual

Page: 155 / 158

154 MG.30.A7.02 - VLT ® is a registered Danfoss trademark
Index
A
About this manual
............................. 5
Acoustic noise .............................. 130
Adaptive motor tuning ..................... 91
Address ........................................ 113
Advanced VLT
®
protection .............. 11
Advancedmotor protection .............. 11
Air humidity ................................... 137
Alarm messages ........................... 126
Alarm mode .................................... 61
Alternative ramp-down time ............ 96
Alternative ramp-up time ................ 96
Analogue reference type ............... 111
Available documentation .................. 5
Avoid unwanted data change ......... 64
B
Base VLT
® 3100-3250 .................... 40
Baud rate ...................................... 113
Binary input 16 .............................. 101
Binary input 18 .............................. 103
Binary input 19 .............................. 104
Binary input 29 .............................. 106
Binary input 32/33 ................ 107, 108
Brake cable ..................................... 56
Brake module ................................. 14
Brake option ................................... 98
Bus bit 11/12 ................................. 117
Bus bit 4 ........................................ 117
Bus jogging 1 ................................ 117
Bus jogging 2 ................................ 117
Bus reference ............................... 117
C
Cable access:
................................. 42
Cables ............................................ 53
Capacitors in the intermediate circuit 8
Carrier frequency ............................ 96
Catch-up / slow-down value ......... 117
Changing a data value: text ............ 65
Choice of frequency converter size 12
Clamp module ................................ 14
Coils in the intermediate circuit ......... 8
Compliance with EMC
directive 89/336/EEC
...................... 53
Connecting ofbrake resistors ........ 146
Connection examples ..................... 32
Connection ofoption cards ............ 146
Constant torque CT ........................ 10
Control accuracy ............................. 10
Control cables ................................. 56
Control card ...................................... 8
Control principle ................................ 8
Control: ........................................... 31
Controller range .............................. 93
Cooling ........................................... 43
Current limit .................................... 95
Current limit control ........................ 89
D
Danfoss VLT
® frequency
converter and CE-labelling ............. 52
Data mode ..................................... 61
Data read-out ....................... 113, 114
Data udlæsning ............................ 115
Data value of aparameter ............... 65
DC brake cut-infrequency ............... 99
DC brake voltage ............................ 99
DC braking time .............................. 99
Derating ........................................ 131
Derating - EMC ............................. 133
Description of terminals ........... 31, 32
Different modes,different
information
..................................... 61
Differentiation time ........................... 93
Digital reference 1
.......................... 94
Digital reference 2 .......................... 94
Digital reference 3 .......................... 94
Digital reference 4 .......................... 94
Digital reference type ...................... 94
Dimensions ..................................... 29
Direction of rotation ........................ 50
Display mode ................................. 61
Display layout ................................... 61
Display messages
........................ 125
Display unit ..................................... 93
Display value .................................. 84
Display valueat min. feedback ........ 92
du/dt and peak voltage on motor .. 130
E
Earth leakage current
................... 128
Earthing: ......................................... 53
Effective radio frequency
interference suppression
................ 11
Effektfaktor ................................... 139
Efficiency ...................................... 138
Electrical installation ....................... 45
Electrical safety ................................ 2
Electrostatic discharge (ESD) ....... 141
EMC installation .............................. 55
Error messages ............................ 127
EXCEPT fault:: ............................. 127
External mounting of the
control panel
................................... 60
External operation ............................ 6
Extreme running conditions .......... 129
F
Factory programmedU/f
characteristics
................................. 10
factory setting ................................... 7
Factory-settings ................... 149, 150
Fault location ................................ 142
Fault messages ............................ 140
Feedback type ................................ 92
FF factor ......................................... 93
Flying start ...................................... 98
For experienced Danfoss VLT users 5
For first-time Danfoss VLT ® users ..... 5
Frequency bypass 1 ....................... 96
Frequency bypass 2 ....................... 96
Frequency bypass 3 ....................... 96
Frequency bypass 4 ....................... 96
Frequency bypassband width ......... 96
Frequency range ............................ 94
Function diagrams .......................... 17
Functions and timers ...................... 98
Functions and timersGroup 3.. ....... 72
G
Galvanic isolation
........................... 11
Galvanic isolation(PELV) .............. 128
General ........................................... 45
Group description ........................... 66
Groups ............................................ 70
H
Heat emission from the VLT® 3000
44
High starting torque ........................ 98
How to use this manual .................... 5
I
If the factory setting has been
changed
............................................ 7
In most cases ................................... 6
Initialization ..................................... 63
Initialization viaparameter ........ 604 63
Inputs and outputs ........................ 101
Inputs and outputsGroup 4.. ........... 72
Integral time .................................... 93
Intermediate circuit ........................... 8
Internal mounting
panel in mounting cabinet IP54
...... 30
Introduction ....................................... 8
Inverter ............................................. 8
IP 00 ............................................... 28
IP 20 ............................................... 28
IP 21 ............................................... 29
IP 21 / IP 54 .................................... 30
IP 54 ............................................... 29
J
JOG frequency(JOG frequency)
..... 94
K
Keys for local operation
.................. 60
Keys for programming .................... 60
L
Language select
............................. 82
LC module ...................................... 14
LC motor filter ................................. 14
Leaving DATA mode ...................... 65
Load ............................................... 88
Load and motor .............................. 88
Load and motorGroup 1.. ............... 66
Local jogging ................................. 85
Local reset ..................................... 84
Local reversing .............................. 85
Local start/stop .............................. 84
Local reference ............................... 85
Local reference(Local speed) ......... 84
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com