manualshive.com logo in svg

Danfoss KPP Pulse Pickup, Technical Information, Page: 14 / 20

Share
Download
Danfoss KPP Pulse Pickup Technical Information Download Page 14

Technical Information 

KPP PPU

11029257

 • Rev BB • July 2013

14

Product Installation

Refer to 

Installation Diagrams

, page 16, regarding these procedures.

Procedure A 

Non-directional KPP flat end models. Models included: KPPG12XXX, KPPG16XXX. Installation steps:

1.  Turn in (CW) by hand until bottom end gently touches the speed ring.

2.  Back out (CCW) 1/2 to 3/4 turn.

3.  Using a 1/2 inch wrench to hold the KPP, torque the lock nut to 13 N•m [10 lbf•ft] with an 11/16 inch 

hex wrench.

Procedures for Flat End and 

Conical End Models

Procedure B:

Directional KPP flat end models. Models included:  KPPG13XXX, KPPG14XXX, KPPG15XXX, KPPG18XXX. 

Installation steps:

1.  Turn in (CW) by hand until bottom end gently touches the speed ring.

2.  Back out (CCW) 1/4 turn. Continue backing out until the flats are 22° (most open-end wrenches 

have a 22° offset) either side of pump or motor shaft center line (20° to 30° is acceptable). Do not 

back out the KPP more than 3/4 of a turn from touching.

3.  Using the 1/2 inch wrench to hold the KPP, torque the lock nut to 13 N•m [10 lbf•ft] with an 11/16 

inch hex wrench.

4.  Special KPP FLAT END models include:  KPPG17XXX, KPPG19XXX, KPPG1AXXX. Installation range is 

application specific:

5.  Turn in (CW) by hand until bottom end gently touches the speed ring.

6.  Back out (CCW) 1/4 turn. Continue backing out until the flats are 22° (most open-end wrenches 

have a 22° offset) either side of pump or motor shaft center line (acceptable range is determined 

per application). Do not back out the KPP more than 3/4 of a turn from touching.

7.  Using the 1/2 inch wrench to hold the KPP, torque the lock nut to 13 N•m [10 lbf•ft] with an 11/16 

inch hex wrench.

Summary of Contents for KPP Pulse Pickup





















Reviews:

No comments