EN
Installation Guide
Danfoss
Icon™
Master Controller 24 V
Connecting more
Danfoss
Icon™
Master Controllers in
a system
If wired system
Connect up to three
Danfoss
Icon
™
Master
Controller 24V
to each other with a 4-wire twisted
pairs cable and the supplied connector .
Cable pin out
1
2
3
1 . GND
2 . COM A
3 . COM B
If wireless system
Wireless connection of up to three
Danfoss
Icon
™
Master Controllers 24V
requires a Radio Module
with each Master / Slave .
Connecting procedure for multiple Danfoss
Icon
™
Controllers in a system
On System Master
1 . Install all thermostats and thermal actuators as
described in the Quick Guide D2 to D6 .
2 . Perform network test . Press
to select
TEST
and
p
ress
to choose
NET TEST
. Confirm
witk
OK
(Quick Guide E7 and E8) .
Pairing Master and Slave
Note! Slave Controllers must be assigned as System
Slaves before assigning outputs and thermostats to
them.
1 . On the selected
system master
, press
to
select
INSTALL
mode .
2 . On the
system slave
, press and hold
for
1,5 sec . The display now toggles between
SLA TYPA
and
SLA TYPB
.
3 . Press
to choose between the two slave
types and confirm with
OK
. See “Slave type
definition” on the next page .
4 . Repeat step 1 – 3 to assign a 2
nd
Slave Controller
to the system (max . two slaves are permitted) .
NET TEST on System Slave
1 . Install all thermostats and actuators as
described in the Quick Guide D2 to D6 .
2 . Perform Network test . Press
to select
TEST
and
p
ress
to choose
NET TEST
. Confirm
with
OK
(Quick Guide E7 and E8) .
3 . After completing the TEST press
to select
RUN
mode and press
OK
(Quick Guide E9) .
APP TEST on System Master
1 . Perform application test . Press
to select
TEST
and
p
ress
to choose
APP TEST
.
Confirm with
OK
(Quick Guide E7 and E8) .
2 . After completing the TEST press
to select
RUN
mode and press
OK
(Quick Guide E9) .
Note! If an Expansion Module is added to the system,
it
must
be installed on the Master Controller.
Changing Slave type
1 . On
Danfoss
Icon
™
Slave Controller press and
hold
for 1 .5 sec . The display now toggles
between
SLA TYPA
and
SLA TYPB
.
2 . Press
to choose between the two slave
types and confirm with
OK
. See “Slave type
definition” for more information .
LINK test on Slave (between Master and Slave)
Press
for 1 .5 sec . The display shows inclusion
pattern while making the LINK test . When done, the
display shows the number of packages recieved in
percentage .
Test procedures for
multiple Danfoss
Icon™
Controllers in a
system
VIMCG30F | 088N3678 | 9
© Danfoss | FEC | 2019 .02
4 (2 x twisted pairs)
Max. 3 x Master
Controllers in one
system.
Summary of Contents for Icon Master
