manualshive.com logo in svg

Danfoss H1 078, Service Manual

Share
Download
Danfoss H1 078 Service Manual Download Page 60

3. Operate vehicle/machine through full range of controls to ensure proper operation.

Charge Pressure Relief Valve

P106 040E

V010

V024

22 mm
52 N•m
[38 lbf•ft]

Pressure Limiter Valve Replacement

Replace the pressure limiter valve as a complete unit. Do not attempt to repair individual components.
See Pressure Limiter Adjustment, page 32, for adjustment instructions.

Removal

Using a 22 mm wrench, remove the pressure limiter valve (L100). Discard O-ring.

Inspection

Inspect the sealing surfaces of the pump for nicks or scratches.

Reassemby

1. Install new O-ring. Lubricate O-ring with petroleum jelly.
2. Replace pressure limiter valve. Torque to the value in the table below.
3. Operate pump at full range of controls to ensure proper machine operation.

Pressure limiter is available as complete unit only. O-ring is available separately.

Service Manual

H1 Pumps 069/078, 089/100, 115/130, 147/165, 210/250

Minor Repair

 

60 | 

©

 Danfoss | May 2018

520L0848 | AX00000087en-US0308

Summary of Contents for H1 078





































































Reviews:

No comments

Brands by name

Popular brands

Load more brands