"o2C"
Default dEF
D02 Config/o2C
D03 Config/o3C
D04 Config/o4C
"no": not used.
"dEF": electric defrost heater/valve for hot gas.
"ALA": alarm output.
"FAn": fan control.
"Lig": light control.
"o3C"
Default FAn
"o4C"
Default Lig
"b1C"
Default noP
Lower left button:
Button 1 Config (short press)/b1C
Button 1 Config (long press)/b1L
Upper left button:
Button 2 Config (short press)/b2C
Button 2 Config (long press)/b2L
Upper right button:
Button 3 Config (short press)/b3C
Button 3 config (long press)/b3L
Lower right button:
Button 4 Config (short press)/b4C
Button 4 Config (long press)/b4L
"b1L"
Default PoF
"b2C"
Default dEF
"b2L"
Default inF
"b3C"
Default tP
"b3L"
Default ECo
"b4C"
Default tn
"b4L"
Default Lig
"PS1"
Min. 0
Max. 999
Default 0
Password level 1 / PS1
Password Level 2 / PS2
Password Level 3 / PS3
These assign passwords to the three levels of access. The password is a
three-digit number. Access levels are Shop, Service and OEM.
You may not therefore have access to change all the passwords.
Passwords are entered by using the up and down arrow buttons.
Danfoss advises against using passwords which are easy to remember
or enter, for example 111, 222, 123 etc.
NOTE: When accessing the controller with 3 wrong password in a sequence
ERC will automatically block access for 15 minutes.
"PS2"
Min. 0
Max. 999
Default 0
"PS3"
Min. 0
Max. 999
Default 0
Ser
Service information settings
The parameters in the following section are READ ONLY and cannot be
changed by the user.
They provide information for technicians and OEM users.
NOTE: the only parameters that can be configured are: "
oEL
", "
oEn
", "
oEH
".
These parameters allow OEMs to enter their own product code.
"ACt"
Accumulated Comp. run time
"AFt"
Accumulated Fan run time
"ALt"
Accumulated Light run time
"AEt"
Accumulated ERC up time
The buttons can be programmed as follows:
Short press function
Long press function (3 s.)
"
noP
": not operating
"
tP
": increase set point
"tn": decrease set point
"
ECo
": toggle Eco mode
"
Lig
": toggle light
"
dEF
": toggle defrost
"
SuP
": toggle super-cool/pull down
"
diP
" : increase display intensity
"
din
" : decrease display intensity
"
CFA
": toggle °C and °F
"
noP
": not operating
"
tP
": increase set point
"
tn
": decrease set point
"
ECo
": toggle Eco mode
"
Lig
": toggle light
"
dEF
": toggle defrost
"
SuP
": toggle super-cool/pull down
"
diP
": increase display intensity
"
din
": decrease display intensity
"
CFA
": toggle °C and °F
"
PoF
": ERC power ON/OFF
"
HoL
": enter holiday mode
"
inF
": enter info menu
"
tEc
": Toggle Winter & Summer Eco mode
NOTE: Your assignments may not be shown on the printed buttons. We advice to
use this functionality together with the fully integrated mounting model only.
1
2
3
4
User Guide | ERC 112D VSC Refrigeration Controller
22 | BC286552322855en-000201
© Danfoss | DCS (vt) | 2019.07