Danfoss ERC 112D VSC User Manual Download Page 2

Application

Advantages

Approvals

Password protected

Temperature control for refrigeration appliances.
Speed control of variable speed compressor.
Front panel mounting.

The latest generation CPU, plenty of memory 
and high-end electronic components allow for 
a uniquely versatile software. Three separate 
password-protected user levels can be used to 
control more than 300 different parameters to fit 
all individual requirements.

R290/R600a end-use applications employing in 
accordance to EN/IEC 60335-2-24, annex CC and 
EN/IEC 60335-2-89, annex BB;
Glow wire according to EN/IEC 60335-1;
IEC/EN 60730
UL60730
NSF
CQC
EAC
Ukraine

The access level can be set separately for each 
parameter using KoolProg Software Tool. 
There are three levels of access 1, 2, 3:
- level 1 is for shop access;
- level 2 for technicians;
- level 3 for OEMs.
The access levels cannot be set using the buttons. 
Passwords for the different levels can however be 
altered for the level of access you have, 
e.g. a level 2 user can change the password for 
level 1 and level 2 but not level 3.

Introduction

User Guide | ERC 112D VSC Refrigeration Controller

2 | BC286552322855en-000201

© Danfoss | DCS (vt) | 2019.07

Summary of Contents for ERC 112D VSC































Reviews: