Danfoss EM-PMI375-T200 User Manual Download | Manualshive

Page: 34 / 77

background image

Risk of electric shock when the connection box is open. When you work with power connections make sure that electricity
is disconnected and rotor rotation is prevented.

Magnetic and electromagnetic elds generated near the current-carrying conductors and permanent magnets in electric
machines represent a health danger to persons with heart pacemakers, metal implants and hearing aids. Persons with a
heart pacemaker, metal implants or hearing aids must consult a doctor before they enter the following areas:

Areas in which electric equipment and parts are operated.

Areas in which electric equipment with permanent magnets are stored, mounted, operated or repaired.

Risk of electric shock when working with the electric machine. Use isolated electric tools.

Only trained and quali ed personnel familiar with the relevant safety requirements can work with the electric machine.

Use correct personal protective equipment when you are near the electric machine.

Read the instructions in this manual before you install the electric machine.

Required tools

Following tools are required to install the electric machine:

Grease pump.
Ratchet torque wrench.
Hex head wrench kit with diﬀerent metric sizes.
Socket wrench kit with diﬀerent metric sizes.
Cable gland tightening tool. Size according to cable glands.
Cable skinning knife.
Crimping tool for cable lugs. Consult cable lug manufacturer for correct size.
Lifting slings with suﬃcient rated capacity.
Lifting eyes. Size according to machine type. See Chapter Lifting.

EM-PMI375

6. Installation

| BC265856307805en-000105

©

Danfoss | Produced By: Danfoss Power Solutions | January 2019 | 33

«
...
32
33
34
35
36
...
»

Summary of Contents for EM-PMI375-T200














































































Reviews:

No comments

Related manuals for EM-PMI375-T200

MICROPUMP DEELE

Brand: Idex Pages: 23

GARDEN SNOWBUSTER (160F)

Brand: Texas Pages: 33

Brand: Baldor Pages: 1

Brand: Lycoming Pages: 83

Brand: Airdog Pages: 28

Brand: Louvolite Pages: 4

Brand: DANA Pages: 2

Brand: DANA Pages: 3

Brand: DANA Pages: 3

Brand: DANA Pages: 3

Brand: DANA Pages: 3

Brand: O.S. engine Pages: 4

Brand: DLE Pages: 4

Brand: Dietz Pages: 12

Brand: Briggs & Stratton Pages: 13

Brand: FAAC Pages: 116

Brand: Mitsubishi Pages: 219

Brand: 3W Pages: 19

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands