Danfoss EM-PMI375-T200 User Manual Download | Manualshive

Page: 43 / 77

background image

Figure 24. BlueGlobe-sealing

2. Cut the cable sheath at the distance A from the end of the cable, see Figure below. Pull the cut

part of the sheath partly (length B is from 10 to 15 mm) oﬀ the cable as shown in the gure. The

distance A depends of the length of the cable lug used. Measure with the cable lug that is used

and cut to suitable lenght.

Do not remove the cable sheath completely at this point and do not cut the braid screen of the cable!

Figure 25. Cut lenght of the cable sheath

3. Insert the cable to the cable gland with slight turning motion. This helps the cable go through

the spring inside the cable gland. Push the cable gland against the sheath of the cable as shown in

Figure below.

EM-PMI375

6. Installation

42 |

©

Danfoss | Produced By: Danfoss Power Solutions | January 2019

| BC265856307805en-000105

«
...
41
42
43
44
45
...
»

Summary of Contents for EM-PMI375-T200














































































Reviews:

No comments

Related manuals for EM-PMI375-T200

Brand: BAFANG Pages: 12

Brand: W&H Pages: 42

Brand: V2 Pages: 14

1550 STERNDRIVE

Brand: Mercury Racing Pages: 75

Brand: Cobra Garden Machinery Pages: 64

Brand: Volvo Penta Pages: 40

Brand: Volvo Penta Pages: 48

Brand: Volvo Penta Pages: 76

Brand: Volvo Penta Pages: 124

Brand: Volvo Penta Pages: 140

Brand: Lycoming Pages: 38

Brand: Haas Pages: 7

Brand: Magnum Pages: 7

Brand: Honda Pages: 32

Brand: Honda Pages: 100

Brand: Homelite Pages: 8

Brand: Stiga Pages: 51

Brand: Gleason Reel Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands