background image

User Guide  |  Liquid level controller, EKE 347 

© Danfoss | DCS (ADAP-KOOL®) | 2016-04

DKRCI.PD.RP0.A4.02 | 4

The user interface of the control panel consists 

of a multiline display and 4 individual push 

buttons: Enter button, Scroll up 

button, Scroll down button and Back 

button.

The figure shows the Home display image, which 

give the actual overview. This is the starting 

point for entering into menus, and you will 

revert to this image by pushing     1 – 3 times 

(depending on actual position).  

Control Panel

The display itself show the state of 

Liquid level, 

Controller Mode

 (controller On/Off), 

Valve 

opening degree, Lower level alarm

 (off = no 

alarm present) and 

Upper level alarm

 (off = no 

alarm present). 

Additional to the external connected alarm 

audio/video sources, a Bell symbol will flash in 

the upper right corner in case of an alarm.

To see more details on system performance and 

setting of parameters, 2 different main menu 

levels can be reached by operation of the push 

buttons. 

From Home image the 

Status menu

 can be 

reached by 

1 push

 on Enter.                                                                     

From Home image the 

Setup & service menu

 

can be reached by 

1 push

 

and hold

 on Enter. 

For entrance a Log In is required by the pass-

word given during Commisioning.

Display

Back

Press and hold = 

Log Out

Scroll up

Scroll down

Enter

Press and hold = 

Log In

Home Image

Controller name

Actual liquid level

Valve opening degree

Flashing bell = Active alarm

Controller mode

Lower level alarm off (pump on)

Upper level alarm off

Summary of Contents for EKE 347



















Reviews: