Danfoss EKC 312 User Manual Download Page 4

4  

 

 

 

DKRCC.PS.R1.A3.02 / 520H9752 

 

© Danfoss A/S (DCS-IMCGPD/sw), 2015-03

Manual 

Electronic superheat controller, type EKC 312

Data

Necessary connections

Terminals:

25-26  Supply voltage 24 V AC.

21-24  Supply to step motor

18-19  Pt1000 sensor at evaporator outlet (S2)

14-15  Pressure transmitter type AKS 33

1-2 

Switch function for start/stop of regulation. If a switch is 

not connected, terminals 1 and 2 must be shortcircuited.

Application dependent connections

Terminal:

18-20  Pt1000 sensor for measuring air temperature (S4)

12-13   Alarm relay

There is connection between 12 and 13 in alarm situa tions 

and when the controller is dead

3-4  

Data communication

 

Mount only, if a data communication module has been 

mounted.

It is important that the installation of the data communi-

cation cable be done correctly. Cf. separate literature No. 

RC8AC...

Connections

Supply voltage

24 V AC +/-15% 50/60 Hz, 10 V A
(the supply voltage is galvanically sepa-
rated from the input and output signals)

Power consumption

Controller
ETS  step motor

5 V A
1,3 V A

Input signal 

Press. transmitter 4-20 mA from AKS 33
Digital input from external contact func-
tion

Sensor input

2 pcs. Pt1000 ohm

Alarm relay

1 pcs. SPST

AC-1: 4 A (ohmic)
AC-15: 3 A (inductive)

Step motor output

Pulsating 100 mA

Data communication

Possible to connect a data 
communication module

Ambient 

temperature

-10 – 55 °C, During operation
-40 – 70 °C, During transport
20 – 80% Rh, not condensed
No shock influence/vibrations

Enclosure

IP 20

Weight

300 g

Mounting

DIN rail

Display

LED, 3 digits

Approvals

EU Low Voltage Directive and EMC 
demands re CE-marking complied with.
LVD-tested acc. to EN 60730-1 
and EN 60730-2-9
EMC-tested acc. to EN50081-1 
and EN 50082-2

Data communication

< --------------- max. 5 m  --------------->

Ordering

Type

Function

Code No.

EKC 312

Superheat controller

084B7250

EKA 173

Data communication module (accessories), 
(FTT 10 module)

084B7092

EKA 175

Data communication module (accessories), 
(RS 485 module)

084B8679

EKA 174

Data communication module (accessories), 
(RS 485 module) with galvanic separation

084B7124

Temperature sensor Pt 1000 ohm / Pressure transmitter type AKS 33: Kindly refer to catalogue 
RK0YG ETS valves: Kindly refer to data sheet RD1TA

Summary of Contents for EKC 312













Reviews: