background image

  

7  

July 31, 2019 

 

6. F5M-IQ DEFAULT TOUCHPAD CONFIGURATION  

 

 

 The touchpad setup is a standard factory default. For setup changes refer to the software manual for program-
ming. The labels can be rearranged as per customer’s preference. 

 

 

 

STBY/PA — 

Momentary AIR HORN (optional can be programmed to momentary WAIL).  

INTER-CLEAR — 

Activates the INTER-CLEAR tone.  

  

NOTE:

 - Activates the MULTI-TONE tone when the system is configured with dual siren amplifier.  

WAIL — 

Activates the WAIL tone.  

YELP — 

Activates the YELP tone.  

STINGER — A

ctivates the STINGER tone  

MANUAL — A

ctivates momentary the WAIL tone.  

AIR HORN — A

ctivates momentary the AIR HORN tone.  

HANDS  FREE

—  The  Hands-Free mode is  activated  when STBY  or  any  of  the siren  buttons  is ON.  A first  

 

press of the horn ring it will activate the WAIL tone. A second press it  will activate the YELP tone. A  

 

third press it will activate the STINGER tone. A fourth press it will activate again the WAIL tone. This  

 

cycle  continues  until  the  user  deactivates  the  Hands-Free  mode.  Pressing  the  horn  ring  twice,  in  a  

 

quick  succession,  when  STBY  is  selected  it  will  turn  OFF  the  siren  tone  and  sets  the  system  into 

 

Hands  -Free ready mode. Pressing the horn ring twice , in a quick succession, when any of the siren 

 

tones is  selected it will turn OFF the siren. Turning OFF the STBY or any of the siren buttons will turn 

 

OFF the  siren tone and deactivates the Hands-Free mode.  

REAR FLASH — 

Activates Output 1 continuous ON and the rear of the lightbar  

FRONT FLASH — A

ctivates Output 2 continuous ON and the front of the lightbar.  

INTERSECTION LIGHTS — 

Activates Output 3 continuous ON and the intersection of the lightbar.  

HEAD LT. FLASH — 

Activates Output 4 & 5 flashing.  

LEFT ALLEY — 

Activates Output 6 continuous ON and the left alley of the lightbar.  

RIGHT ALLEY — 

Activates Output 7 continuous ON and the right alley of the lightbar.  

MASTER — 

Activates STBY, REAR FLASH, FRONT FLASH, INTERSECTION LIGHTS buttons.  

TAKE DOWN — 

Activates Output 8 continuous ON and the take down of the lightbar.   

CONTROL — 

Activates Output 9 as 9 second timer, with IGNITION ON only.  

AUX 1 — 

Activates Output 10 continuous ON.  

AUX 2 — 

Activates Output 11 continuous ON.  

ANTI-THEFT — 

Activates Output 12 MOMENTARY, with IGNITION ON only.  

ARROW DIRECT — 

Activates Output 13 & Output 14 as 2 trigger traffic director:   

  

  

  

  

LEFT ARROW—Output 13 continuous ON  

  

  

  

  

RIGHT ARROW—Output 14 continuous ON  

  

  

  

  

CENTER OUT—Output 13 & Output 14 continuous ON  

Summary of Contents for F5M-IQ













Reviews: