background image

 

Z5577.000 Front panel

3.1. Intended use
The Z5577.000 Mains power distributor is designed and

dimensioned to provide and distribute the mains power supply

necessary for 

one Z5576.000 Touring rack assembly.

It is a protective class 1 unit with IP class 20 (NOT rain-, drip-, or

splash-proof!).

The Z5577.000 Mains power distributor must not be used for any

other purpose or outside the system rack.

3.2. Rear panel
3.2.1. MAINS IN

WARNING!
Potential risk of electric shock.

The mains power distributor is a protective class 1 unit. A missing

earth (ground) contact may cause dangerous voltages in the

housing and controls and may lead to electric shock.
▪ Connect the unit to mains power supplies with protective earth

only.

▪ If there is any sign of obvious damage to the power cord

and/or CEE mains connector, do not use the unit and replace it

before further use.

▪ Do not connect or disconnect the CEE mains connector under

load or live.

▪ Please ensure the mains connector is accessible at any time to

disconnect the unit in case of malfunction or danger.

Apart from the six fixed single-phase mains power lines (6 x

MAINS TO AMPS 230 V) for the internal mains power supply of

the amplifiers, the Z5577.000 Mains power distributor is supplied

with a fixed 3-phase power cord equipped with a 32 A CEE

(Cekon) mains connector.

Required mains supply network configuration

3-phase 230/400 VAC - 50/60 Hz - 32 A

max.

 (3PNPE).

Connect only 

one rack assembly to the mains power outlet of the

onsite sub-distribution.

The Z5577.000 Mains power distributor does not provide

dedicated circuit-breakers for the amplifier's mains power lines. The

respective circuit-breakers of the onsite mains distribution are used

for this purpose.

Z5577.000 Rear panel

3. Z5577.000 Mains power distributor 32 A CEE

 

d&b Z5576.000 Manual 1.1 en

8

Summary of Contents for Z5576.000























Reviews: