Choix de l’emplacement :
Choisir un emplacement approprié, avec accès facile à
une prise de courant (éviter l’emploi d’une rallonge). S’il
est absolument nécessaire d’utiliser une rallonge pour
l’alimentation de l’appareil, utiliser uniquement une
rallonge agréée pour climatiseur (disponible dans la
plupart des magasins de quincaillerie)
Choisir un emplacement où rien n’entravera la
circulation de l’air à travers la grille d’admission avant.
Maintenir une distance de séparation d’au moins 20 cm
entre les murs adjacents et l’arrière de l’appareil, pour
optimiser l’efficacité et la circulation de l’air.
L’appareil fonctionne au niveau d’efficacité maximum
lorsque la température ambiante de la pièce est située
entre 6ºC et 35ºC.
Il est important de noter que l’efficacité d’un
déshumidificateur sera influencée par la taux de
réintroduction d’air humide dans la pièce. Pour obtenir
la meilleure efficacité, il convient de faire fonctionner le
déshumidificateur dans un espace ferme. Fermer
toutes les portes et fenêtres.
20
INSTALLATION
8
Indicator Light Function:
Power Light (Green):
When the unit is first connected to an electrical outlet,
the (green) power light starts to flash and continues to
flash until the “on/off” button is pressed. When the “on/off”
button is activated, the flashing (power) light turns to a
steady state “on” condition. The dehumidifier will
automatically default to the factory default setting. (See
Factory Default Setting for details)
IMPORTANT NOTE:
Depending on the humidity
conditions of the surrounding environment, the
dehumidifier may not start automatically when the “on/off”
button is pressed.(see dehumidifier operating instructions
for details)
In the event of a power failure, the unit will not re-start
automatically when power is restored. To re-start the unit
you must press the "on/off" keypad again.
Water Full Indicator Light (Red):
When the water tank is full and /or incorrectly positioned
inside the cabinet, the (water full) red light turns on and
remains on until such time the tank is emptied and/or
correctly re-positioned. This condition will result in the
immediate shut down of the dehumidifying system. (both
compressor and fan motor operation are terminated) This
is a safety feature. When the water tank is emptied and/or
correctly re-positioned, the dehumidifier will resume
operation automatically.
NOTE: It may take several
minutes before operating conditions resume.
Factory Default Setting:
Each time the unit is disconnected/re-connected and/or in
the event of a power failure, the electronic circuit board
automatically defaults to the following factory setting.
Humidity Setting: 60%
Fan Speed:
Low
NOTE:
In the event of a power failure, all previous settings
are automatically erased/cancelled. If your program
setting was different than the above (default setting) it will
be necessary to re-program your settings. When the unit
is switched "Off” manually (using the on/off keypad) the
unit will always default to the last program setting that
was used.
Water Tank Operation:
Proper installation of the water tank is crucial in
maintaining reliable dehumidifier operation.
The water tank holds accumulated condensed water and
by means of a safety switch controls both the water level
and operation of the dehumidification process.
i.e. When the water tank is full and/or accidentally
displaced inside the cabinet, the float switch actuator
(inside the tank) breaks contact with the safety switch.
This condition results in the immediate shut down of the
compressor and fan motor system, preventing moisture
from being condensed.
IMPORTANT:
Never tamper with or attempt to defeat the
water level (safety) float switch system.
Operating Instructions
Summary of Contents for ArcticAire ADR4066
Page 2: ......
