DANA Brevini Posiplan BPH Series Installation And Maintenance Manual Download Page 9 | Manualshive

Page: 9 / 40

background image

9

Dana Incorporated

IMM-0005EN Posiplan (MT-5215-0806)

DELIVERY STATE:

Gear units are externally finished with a synthetic nitro-epoxy primer al nitro “RAL 5010”, unless otherwise specified in the sales
agreement. Such protection withstands normal industrial environments, including outdoor applications. If the machine is to be
used in particularly aggressive conditions, a special paint finish will be required. External machined parts of the gear unit, such
as the ends of the hollow and non-hollow shafts, support surfaces, alignment pins, etc. are protected with a rust-inhibitor oil
(tectyl). Internal parts of the gear unit casings and drives are also protected with rust-inhibitor oil. Unless otherwise specified in
the sales agreement, all gear units are supplied unlubricated; this is clearly stated on an adhesive label attached to the gear unit.

«
...
7
8
9
10
11
...
»

Summary of Contents for Brevini Posiplan BPH Series









































Reviews:

No comments

Related manuals for Brevini Posiplan BPH Series

Brand: GBC Pages: 8

Brand: KAPSCH Pages: 57

Brand: Malmet Pages: 14

Brand: Zempire Pages: 2

Brand: Bante Instruments Pages: 6

Brand: SAMCHULLY Pages: 48

Brand: HAGER WERKEN Pages: 2

Brand: V.ORLANDI Pages: 144

Brand: Yamaha Pages: 39

Brand: Yamaha Pages: 110

Brand: ubicquia Pages: 36

C-HB-A-LB2-SCCT Series

Brand: C-LITE Pages: 9

X-431 Torque HD

Brand: Launch Pages: 3

Brand: Rigol Pages: 12

Brand: Garmat Pages: 13

Brand: Gama Sonic Pages: 4

Tracer DO PockeTester

Brand: LaMotte Pages: 19

Brand: Deltech Fitness Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands